PDF p. 1212 · 23-E-18
- 1.Remove the driver’s lower pocket (see section 20).
- 2.Disconnect the 14P connector from the control unit.
- 3.Inspect the connector and socket terminals to make sure they are all making good contact.
- If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
- If the terminals look OK, make the following input tests at the connector.
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, the control unit must be faulty, replace it.

- 1. BLU/WHT
- 2. BLU/RED
- 3. YEL/RED
- 4. WHT/RED
- 5. WHT/GRN
- 6. Wire side of female terminals
- 7. BLU/BLK
- 8. LT GRN/RED
- 9. BLK
- 10. YEL
- 11. GRN/RED
- 12. BLU/RED
- 13. 14P CONNECTOR
- 14. KEYLESS DOOR LOCK CONTROL UNIT
Disconnect the 14P connector from the keyless door lock control unit
| Cavity | Wire | Test condition | Test: Desired result | Possible cause if result is | |
|---|---|---|---|---|---|
| not obtained | |||||
| 12 | BLK | Under all conditions | Check for continuity to ground: | ♦ | Poor ground (G401, G402) |
| There should be continuity | ♦ | An open in the wire | |||
| 4 | YEL/RED | Connect the No. 4 | Check door lock operation: | ♦ | Faulty actuator |
| terminal to the No. 6 | All doors should unlock | ♦ | An open in the wire | ||
| terminal and the No. 5 | ♦ | Blown No. 25 (15A) fuse in | |||
| terminal to the No. 12 | the under-dash fuse/relay box | ||||
| terminal momentarily | |||||
| 5 | WHT/RED | Connect the No. 5 | Check door lock operation: | ♦ | Faulty actuator |
| terminal to the No. 6 | All doors should unlock | ♦ | An open in the wire | ||
| terminal and the No. 4 | ♦ | Blown No. 25 (15A) fuse in | |||
| terminal to the No. 12 | the under-dash fuse/relay box | ||||
| terminal momentarily | |||||
PDF p. 1213 · 23-E-19
Reconnect the 14P connector to the keyless door lock control unit.
| Cavity | Wire | Test condition | Test: Desired result | Possible cause if result is | |
|---|---|---|---|---|---|
| not obtained | |||||
| 6 | WHT/GRN | Under all conditions | Check for voltage to ground: | ♦ | Blown No. 25 (15A) fuse in |
| There should be battery voltage | the under-dash fuse/relay box | ||||
| ♦ | An open in the wire | ||||
| 1 | BLU/WHT | Driver’s door lock knob | Check for voltage to ground: | ♦ | Faulty driver’s door lock |
| in LOCK | There should be 1V or less | actuator | |||
| ♦ | An open in the wire | ||||
| ♦ | Poor ground (G401, G402) | ||||
| 7 | BLU/RED | Driver’s door lock knob | Check for voltage to ground: | ♦ | Faulty driver’s door lock |
| in UNLOCK | There should be 1V or less | actuator | |||
| ♦ | An open in the wire | ||||
| ♦ | Poor ground (G401, G402) | ||||
| 3 | BLU/RED | Ignition key in the | Check for voltage to ground: | ♦ | Faulty ignition key switch |
| ignition switch | There should be 1V or less | ♦ | An open in the wire | ||
| ♦ | Poor ground (G401, G402) | ||||
| 11 | YEL | Ignition switch ON (II) | Check for voltage to ground: | ♦ | Blown No. 6 (7.5A) fuse in |
| There should be battery voltage | the under-dash fuse/relay box | ||||
| ♦ | An open in the wire | ||||
| 14 | BLU/BLK | Tailgate open/close | Check for voltage to ground: | ♦ | Faulty tailgate latch switch |
| There should be 1V or less when | ♦ | An open in the wire | |||
| the tailgate is opened | ♦ | Poor ground (G501) | |||
| There should be battery voltage | |||||
| when the tailgate is closed | |||||
| 10 | GRN/RED | Passenger’s door | Check for continuity to ground: | ♦ | Faulty door switch |
| opened | There should be continuity | ♦ | An open in the wire | ||
| 13 | LT | All doors closed and | Connect to ground: | ♦ | Blown No. 23 (7.5A) fuse in |
| GRN/RED | front ceiling light | Front ceiling light should come on | the under-dash fuse/relay box | ||
| switch position | ♦ | Blown front ceiling light bulb | |||
| MIDDLE | ♦ | An open in the wire | |||