Workshop manual

Seats

Front Seat Disassembly and Reassembly

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 991, 992 (manual pages 20-55 to 20-56)

PDF p. 991 · 20-55

NOTE:

  • Take care not to scratch the body or tear the seat covers.
  • When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. Driver’s:
Illustration: HEADREST; Forward; HOOK; SEAT CUSHION; 10 x 1.25 mm 47 Nm (4.8 kgf/m, 35 lbf/ft); RECLINE COVER; RECLINE LEVER; RECLINE ADJUSTER/OUTER SEAT TRACK; CONNECTING WIRE; INNER SEAT TRACK; CENTRE COVER; END CAP; BUSHING 14 END CAPS; CLIP; PIVOT NUT, 8 x 1.25 mm 22 Nm (2.2 kgf/m, 16 lbf/ft); PIVOT WASHER; SEAT-BACK
  1. 1. HEADREST
  2. 2. Forward
  3. 3. HOOK
  4. 4. SEAT CUSHION
  5. 5. 10 x 1.25 mm 47 Nm (4.8 kgf/m, 35 lbf/ft)
  6. 6. RECLINE COVER
  7. 7. RECLINE LEVER
  8. 8. RECLINE ADJUSTER/OUTER SEAT TRACK
  9. 9. CONNECTING WIRE
  10. 10. INNER SEAT TRACK
  11. 11. CENTRE COVER
  12. 12. END CAP
  13. 13. BUSHING
    14 END CAPS
  14. 15. CLIP
  15. 16. PIVOT NUT, 8 x 1.25 mm
    22 Nm (2.2 kgf/m, 16 lbf/ft)
  16. 17. PIVOT WASHER
  17. 18. SEAT-BACK

PDF p. 992 · 20-56

Passenger’s:

Illustration: HEADREST; Forward; HOOK; PIVOT NUT, 8 x 1.25 mm. (22 Nm 2.2 kgf/m, 16 lbf/ft); PIVOT WASHER; SEAT CUSHION; CLIP; CENTRE COVER; 10 x 1.25 mm 47 Nm (4.8 kgf/m, 35 lbf/ft); INNER SEAT TRACK; RECLINE CABLE; RECLINE ADJUSTER/OUTER SEAT TRACK; RECLINE COVER 14 RECLINE LEVER; END CAPS; CONNECTING WIRE; END CAP; BUSHING; SEAT COVER; SEAT-BACK
  1. 1. HEADREST
  2. 2. Forward
  3. 3. HOOK
  4. 4. PIVOT NUT, 8 x 1.25 mm. (22 Nm 2.2 kgf/m, 16 lbf/ft)
  5. 5. PIVOT WASHER
  6. 6. SEAT CUSHION
  7. 7. CLIP
  8. 8. CENTRE COVER
  9. 9. 10 x 1.25 mm 47 Nm (4.8 kgf/m, 35 lbf/ft)
  10. 10. INNER SEAT TRACK
  11. 11. RECLINE CABLE
  12. 12. RECLINE ADJUSTER/OUTER SEAT TRACK
  13. 13. RECLINE COVER
    14 RECLINE LEVER
  14. 15. END CAPS
  15. 16. CONNECTING WIRE
  16. 17. END CAP
  17. 18. BUSHING
  18. 19. SEAT COVER
  19. 20. SEAT-BACK

Reassembly in the reverse order of disassembly and note the following items:

  • Make sure the bushing and pivot washer are installed properly.
  • To connect the connecting wire, twist it 90°.
  • Replace the back cover clips with new ones.
  • To prevent wrinkles when installing the seat-back cover, make sure the material is stretched evenly over the pad.
  • Apply multipurpose grease to the moving portion of the seat track.