Workshop manual

Glass

Rear Window Replacement

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 961, 962, 963, 964 (manual pages 20-25 to 20-28)

PDF p. 961 · 20-25

NOTE:

  • Wear gloves to remove and install the rear window.
  • Use seat covers to avoid damaging any surfaces.
  • Do not damage the rear window defogger grid lines and terminals.
  • Use glass adhesive set P/N, 08C73-X0230N.
  1. 1.
    Remove:
    • High mount brake light (see section 23).
    • Tailgate trim panel (See Page 20-42).
    • Rear window wiper arm (See Page 20-23).
  2. 2.
    Disconnect the rear window defogger connectors.
Illustration: REAR WINDOW DEFOGGER CONNECTOR
  1. 1. REAR WINDOW DEFOGGER CONNECTOR
  1. 3.
    Apply protective tape. Using an awl, make a hole through the adhesive from inside the vehicle. Push piano wire through the hole and wrap each end around a piece of wood.
  2. 4.
    With a helper on the outside, pull the piano wire back and forth in a sawing motion. Hold the piano wire as close to the rear window as possible to prevent damage to the tailgate. Carefully cut through the rubber dam and adhesive around the entire rear window.
  3. 5.
    Carefully remove the rear window.
  1. 6.
    With a putty knife, scrape the old adhesive smooth to a thickness of about 2 mm (0.08 in) on the bonding surface around the entire rear window opening flange.
    • Do not scrape down to the painted surface of the tailgate; damaged paint will interfere with proper bonding.
    • Mask off surrounding surfaces before painting.
    • Remove the rubber dams and fasteners from the tailgate.
  2. 7.
    Clean the tailgate bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the clean surface.
  3. 8.
    If the old rear window is to be reinstalled, use a putty knife to scrape off all traces of old adhesive on the rubber dams and the fasteners from the rear window, then clean the rear window surface and edge with alcohol where new adhesive is to be applied. Make sure the bonding surface is kept free of water, oil and grease.

PDF p. 962 · 20-26

  1. 9.
    Glue the fasteners and rubber dams to the inside face of the rear window as shown:
    • Be sure the fasteners and rubber dams line up with the alignment marks.
    • Be careful not to touch the rear window where adhesive will be applied.

: Fastener locations

Illustration · Glass · Rear Window Replacement

1, ALIGNMENT MARK

  1. 2.
    REAR WINDOW MOLDING
  2. 3.
    RUBBER DAM
  3. 4.
    REAR WINDOW
  4. 5.
    LOWER RUBBER DAM
  5. 6.
    UPPER RUBBER DAM
  1. 10.
    Glue the fasteners to the tailgate.
Illustration: FASTENER
  1. 1. FASTENER
  1. 11.
    Set the rear window in the opening and centre it. Make alignment marks across the rear window, tailgate and body with a grease pencil at the four points shown. Be careful not to touch the rear window where adhesive will be applied.
Illustration: ALIGNMENT MARK; PIN; LOWER FASTENER; REAR WINDOW
  1. 1. ALIGNMENT MARK
  2. 2. PIN
  3. 3. LOWER FASTENER
  4. 4. REAR WINDOW
  1. 12.
    Remove the rear window

PDF p. 963 · 20-27

  1. 12.
    With a sponge, apply a light coat of glass primer around the edge of the rear window as shown, then lightly wipe it off with gauze or cheesecloth:
    • Do not apply body primer to the rear window and not do get tailgate and glass primer sponges mixed up.
    • Never touch the primed surfaces with your hands. If you do, the adhesive may not bond to the rear window properly, causing a leak after the rear window is installed.
    • Keep water, dust and abrasive materials away from the primed surface.
Illustration: Apply glass primer here.; REAR WINDOW; RUBBER DAM; Inside.; REAR WINDOW MOLDING; LOWER RUBBER DAM; UPPER RUBBER DAM
  1. 1. Apply glass primer here.
  2. 2. REAR WINDOW
  3. 3. RUBBER DAM
  4. 4. Inside.
  5. 5. REAR WINDOW MOLDING
  6. 6. LOWER RUBBER DAM
  7. 7. UPPER RUBBER DAM
  1. 13.
    With a sponge, apply a light coat of body primer to the original adhesive remaining around the rear window opening flange. Let the body primer dry for at least 10 minutes:
    • Do not apply glass primer to the body and be careful not to mix up glass and body primer sponges.
    • Never touch the primed surfaces with your hands.
Illustration: Apply body primer here.
  1. 1. Apply body primer here.
  1. 14.
    Before filling a cartridge, cut a “V” in the end of the nozzle as shown.
Illustration: NOZZLE
  1. 1. NOZZLE

PDF p. 964 · 20-28

  1. 14.
    Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a caulking gun and run a bead of adhesive around the edge of the rear window as shown. With the printed dots on the rear window as guide, apply the adhesive to both side portions of the rear window. Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker bead at each corner.
Illustration: ADHESIVE; REAR WINDOW; RUBBER DAM; Inside; REAR WINDOW MOLDING; LOWER RUBBER DAM; UPPER RUBBER DAM
  1. 1. ADHESIVE
  2. 2. REAR WINDOW
  3. 3. RUBBER DAM
  4. 4. Inside
  5. 5. REAR WINDOW MOLDING
  6. 6. LOWER RUBBER DAM
  7. 7. UPPER RUBBER DAM
  1. 15.
    Use suction cups to hold the rear window over the opening, align it with the alignment marks you made in step 11, and set it down on the adhesive. Lightly push on the rear window until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until the adhesive is dry.
  2. 16.
    Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the rear window, use a soft shop towel dampened with alcohol.
  3. 17.
    Let the adhesive dry for at least one hour, then spray water over the rear window and check for leaks. Mark the leaking areas, let the rear window dry, then seal with sealant.
    • Let the vehicle stand for at least four hours after rear window installation. If the vehicle has to be used within the first four hours, it must be driven slowly.
    • Keep the rear window dry for the first hour after installation.
  4. 18.
    Reinstall all remaining removed parts. Advise the customer not to do the following things for two to three days:
    • Slam the doors with all the windows rolled up.
    • Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads).