PDF p. 956 · 20-20
NOTE:
- Wear gloves to remove and install the windshield.
- Use seat covers to avoid damaging any surfaces.
- Use glass adhesive set, P/N, 08C73-X0230N.
- 1.Remove:
- Rearview mirror (with roof spoiler, (See Page 20-16).
- Grab handles (both sides as necessary, (See Page 20-44).
- Door trim (both sides as necessary, (See Page 20-41).
- Front pillar trim (both sides, (See Page 20-41).
- Windshield wiper arms and cowl cover (see section 23)
- 2.Remove the Molding and glass bracket. If necessary, cut the Molding with a utility knife.

- 1. MOLDING
- 2. WINDSHIELD
- 3. ADHESIVE
- 4. GLASS BRACKET, 2
- 3.Pull down the front portion of the headliner (See Page 20-44). Take care not to bend the headliner excessively, or you may crease or break it.
- 4.Apply protective tape. Using an awl, make a hole through the rubber dam adhesive and dashboard seal from inside the vehicle. Push piano wire through the hole and wrap each end around a piece of wood.
- 5.With a helper on the outside, pull the piano wire back and forth in a sawing motion. Hold the piano wire as close to the windshield as possible to prevent damage to the body and dashboard. Carefully cut through the rubber dam and adhesive around the entire windshield.
- 6.Carefully remove the windshield.
- 7.With a knife, scrape the old adhesive smooth to a thickness of about 2 mm (0.08 in) on the bonding surface around the entire windshield opening flange:
- Do not scrape down to the painted surface of the body; damaged paint will interfere with proper bonding.
- Remove the rubber dam and fasteners from the body.
- Mask off surrounding surfaces before painting.
- 8.Clean the body bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the clean surface.
- 9.If the old windshield is to be reinstalled, use a putty knife to scrape off all traces of old adhesive from the windshield, the rubber dam and the dash board seal, then clean the windshield surface and edge with alcohol where new adhesive is to be applied. Make sure the bonding surface is kept free of water, oil and grease.
PDF p. 957 · 20-21
- 10.Glue the upper rubber dam, lower rubber dam and fasteners to the inside face of the windshield as shown:
- Be sure the rubber dam, fasteners and dashboard seal line up with the alignment marks.
- Be careful not to touch the windshield where adhesive will be applied.

- 1. WINDSHIELD
- 2. UPPER RUBBER DAM
- 3. ALIGNMENT MARK
- 4. FASTENER
- 5. LOWER RUBBER DAM
- 6. Inside
- 7. RUBBER DAM
- 11.Apply primer (3M N-200, or equivalent) to the areas between the alignment marks of the windshield. Glue the Molding with adhesive tape to the edge of the windshield:
- Be sure the alignment mark of the Molding line up with the alignment mark of the windshield.
- Be careful not to touch the windshield where adhesive will be applied.

- 1. Apply primer here.
- 2. ALIGNMENT MARKS
- 3. MOLDING
- 4. ADHESIVE TAPE
- 5. WINDSHIELD
- 6. Inside
- 7. ALIGNMENT MARK
PDF p. 958 · 20-22
- 12.Glue the molding upper seal and molding side seal to the molding. Be careful not to touch the windshield where adhesive will be applied.

- 1. MOLDING UPPER SEAL
- 2. MOLDING
- 3. ALIGNMENT MARK
- 4. WINDSHIELD
- 5. MOLDING SIDE SEAL
- 13.Install the fastener and glass brackets to the body.

- 1. FASTENER
- 2. ALIGNMENT MARK
- 3. GLASS BRACKET
- 14.Set the windshield in the opening and centre it. Make alignment marks across the windshield and body with a grease pencil at the four points shown. Be careful not to touch the windshield where adhesive will be applied.

- 1. WINDSHIELD
- 2. ALIGNMENT MARK
- 3. GLASS BRACKET
NOTE: Adjust the glass bracket to centre the windshield in the opening, then tighten the screws. - 4. SCREW
- 15.Remove the windshield.
PDF p. 959 · 20-23
- 16.With a sponge, apply a light coat of glass primer around the edge of the windshield between the rubber dam and molding as shown, then lightly wipe if off with gauze or cheesecloth:
- Apply glass primer to the molding.
- Do not apply body primer to the windshield and do not get body and glass primer sponges mixed up.
- Never touch the primed surfaces with your hands. If you do, the adhesive may not bond to the windshield properly, causing a leak after the windshield is installed.
- Keep water, dust and abrasive materials away from the primed surface.

- 1. Apply glass primer here.
- 2. RUBBER DAM
- 3. MOLDING
- 4. Inside
- 5. WINDSHIELD
- 6. LOWER RUBBER DAM
- 7. FASTENER
- 8. UPPER RUBBER DAM
- 17.With a sponge, apply a light coat of body primer to the original adhesive remaining around the windshield opening flange. Let the body primer dry for at least 10 minutes:
- Do not apply glass primmer to the body and be careful not to mix up glass and body primer sponges.
- Never touch the primed surfaces with your hands.
- Mask off the dashboard before painting the flange.

- 1. Apply glass primer here.
- 18.Before filling a cartridge, cut a “V” in the end of the nozzle as shown.

- 1. NOZZLE
PDF p. 960 · 20-24
- 18.Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a caulking gun and run a bead of adhesive around the edge of the windshield between the rubber dam and molding as shown. Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker bead at each corner.

- 1. ADHESIVE
- 2. MOLDING
- 3. Inside
- 4. WINDSHIELD
- 5. RUBBER DAM
- 19.Use suction cups to hold the windshield over the opening, align it with the alignment marks made in step 14 and set it down on the adhesive. Lightly push on the windshield until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until adhesive is dry.
- 20.Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the windshield, wipe with a soft shop towel dampened with alcohol.
- 21.Let the adhesive dry for at least one hour, then spray water over the windshield and check for leaks. Mar leaking areas and let the windshield dry, then seal with sealant:
- Let the vehicle stand for at least four hours after windshield installation. If the vehicle has to be used within the first four hours, it must be driven slowly.
- Keep the windshield dry for the first hour after installation.
- 22.Reinstall all remaining removed parts. Install the rearview mirror after the adhesive has dried thoroughly. Advise the customer not to do the following things for two to three days:
- Slam the doors with all the windows rolled up.
- Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads).