Workshop manual

UP Resin Parts

Refinishing Procedures

Body Repair Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1711, 1712 (manual pages 9-17 to 9-18)

PDF p. 1711 · 9-17

  1. 1.
    Base material reconditioning (sanding)
    1. -1.

      Replacement part.

      Lightly sand both sides of the part.

    2. -2.

      Slight scores or scratches.

      Use a flexible sanding block and wet-sand the damaged section with #400, #600.

      NOTE: Sand level to remove damage.

    3. -3.

      Deep scratches, when filling.

      Use a flexible sanding block and wet-sand the damaged section with #400, #600.

NOTE: Perform the featheredge on the material surface and coat surface (primer, intermediate coat and top coat) thoroughly and properly).

  • Polish the levelled area with #400 sandpaper
  1. 2.

    Degreasing/Cleaning

    Clean the repair area with wax and grease remover, then blow dry with air.

NOTE: Wipe dust off the surface with a tack cloth.

  1. 3.
    Primer application
    • Apply to the deep scratches and areas to be filled. This procedure might not be required by some manufacturer’s products.
    • Spray wider than the damaged section (i.e. area to be filled) two to three times.

NOTE: Follow the manufacturer’s specifications.

  1. 4.

    Coating with primer surfacer and drying

    NOTE: Some manufacturer’s might require puttying before performing this step.

    Spray the primer surfacer wider than the filled area and the exposed base material.

    The spray guideline should be 20 - 23 microns.

NOTE: Follow the manufacturer’s instructions.

  • After coating with the primer surfacer, let the primer surfacer dry naturally for 5 to 10 minutes, then dry the paint film of the primer surfacer with an infra-red dryer.
  • When drying the primer surface with the dryer, be sure to keep the dryer 40 - 50 cm (16 - 20in) away from the paint film.
  1. 5.
    Filling, drying and sanding
    • The exposed base material could be directly filled, depending on the manufacturer’s specification.
    • Be sure that the primer surfacer is completely dry.
    • Lightly dry sand the primer surfacer paint film with the #240 paper.

PDF p. 1712 · 9-18

  • Apply the filler in several thin coats.

NOTE: Mix and apply the filler according to the manufacturer’s instructions.

  • Dry the filler with an infra-red dryer for 5 to 6 minutes.
  • While drying the filler with the dryer, be sure to keep the dryer 40 -50 cm (16 - 20 in) away from the surface.
  • Scratch the filled surface with your nail. If the surface is white when scratched, dry sand and wet sand with the #280, #320 paper. Be sure to sand level.
  1. 6.

    Cleaning with compressed air and degreasing

    Blow the entire area that is to be coated with primer surfacer, with compressed air then clean with wax and grease remover.

NOTE: Also wipe the masking area to help the masking tape adhere securely.

  1. 7.

    Masking

    ♦. Mask the area that should not be sprayed with the

    primer surfacer.

    • Use the masking tape and paper to mask.
  2. 8.

    Coating with primer surfacer and drying

    ♦. Spray the two primer surfacer over the filled area.

    • The spray guideline should be 20 - 25 microns.

NOTE: Follow the primer surfacer manufacturer’s instructions.

  • After coating with the primer surfacer, let the primer surfacer dry naturally for 5 to 10 minutes, then dry with an infra-red dryer.
  • While drying with the dryer, be sure to keep the dryer 40 -50 cm (16 - 20 in) away from the paint film.
  1. 9.

    Sanding and cleaning

    Lightly wet-sand the whole area to be painted with #600 sandpaper. Blow off with compressed air, then clean with wax and grease remover.

  2. 10.
    Top coating
    • Remove dust with a tack cloth before top coating.
    • Spray the top coat paint.

      Spray until the primer surfacer is covered. The spray guideline should be 30 -35 microns.

NOTE: For the recommended top coat paint, refer to the “4 Top coat” of “Example of repair materials”.

Solid:Colour enamel + colour clear coat.
Metallic:Metallic enamel + clear coat.
Pearl:Pearl enamel + clear coat.
  1. 11.

    Drying

    After top coating about 10 minutes, dry with an infra-red dryer.

    NOTE: Follow the paint manufacturer’s specification to dry properly.