Workshop manual

Master Cylinder/Brake Booster

Reassembly

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 892, 893 (manual pages 19-A-15 to 19-A-16)

PDF p. 892 · 19-A-15

NOTE:

  • If replacing the primary piston, secondary piston or master cylinder body. Check and adjust the pushrod clearance before installing the master cylinder (See Page 19-A-17).
  • Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
  • Before reassembling, check that all parts are free of dust and other foreign particles.
  • Replace parts with new ones whenever specified to do so.
  • Do not mix different brands of brake fluid as they may not be compatible.
  • Do not reuse the drained fluid. Use only clean Genuine Honda brake fluid or an equivalent DOT3 or DOT4 brake fluid.
  • Replace the master cylinder if the bore is damaged or worn. Do not hone or attempt to refinish the bore.
  • Coat the piston cups, pressure cup and master cylinder bore with clean brake fluid.
  • Use recommended greases in the master cylinder seal set.
  1. 1.
    Install the reservoir seal in the groove of the reservoir cap.
  2. 2.
    Install the new grommets, strainer and reservoir cap on the reservoir.
  3. 3.
    Install the reservoir on the master cylinder.
Illustration: RESERVOIR CAP; RESERVOIR SEAL; STRAINER; 3 Nm (0.3 kgf/m, 2 lbf/ft); RESERVOIR; MASTER CYLINDER; GROMMETS, Replace; SECONDARY CUP; CIRCLIP, Replace; ROD SEAL, Replace; SECONDARY PISTON, Replace; PRIMARY PISTON, Replace
  1. 1. RESERVOIR CAP
  2. 2. RESERVOIR SEAL
  3. 3. STRAINER
  4. 4. 3 Nm (0.3 kgf/m, 2 lbf/ft)
  5. 5. RESERVOIR
  6. 6. MASTER CYLINDER
  7. 7. GROMMETS, Replace
  8. 8. SECONDARY CUP
  9. 9. CIRCLIP, Replace
  10. 10. ROD SEAL, Replace
  11. 11. SECONDARY PISTON, Replace
  12. 12. PRIMARY PISTON, Replace

PDF p. 893 · 19-A-16

  1. 4.
    Coat the cups of a new primary piston with clean brake fluid, then install the primary piston into the master cylinder.
Illustration: CUPS; PRIMARY PISTON, Replace
  1. 1. CUPS
  2. 2. PRIMARY PISTON, Replace
  1. 5.
    Apply the recommended rubber grease in the master cylinder seal set to the piston cup of a new secondary piston.
  2. 6.
    Coat the cup of a new secondary piston with clean brake fluid, then install the secondary piston into the master cylinder.
Illustration: CUP; SECONDARY CUP; SECONDARY PISTON, Replace
  1. 1. CUP
  2. 2. SECONDARY CUP
  3. 3. SECONDARY PISTON, Replace
  1. 7.
    Install a new circlip while pushing in the secondary piston.
  2. 8.
    Apply the recommended seal grease in the master cylinder seal set to a new rod seal and install it onto the mating face of the brake booster.
Illustration: Brake booster side; ROD SEAL, Replace; Master cylinder side; MASTER CYLINDER; CIRCLIP, Replace
  1. 1. Brake booster side
  2. 2. ROD SEAL, Replace
  3. 3. Master cylinder side
  4. 4. MASTER CYLINDER
  5. 5. CIRCLIP, Replace
  1. 9.
    Adjust the pushrod clearance (See Page 19-A-17).
  2. 10.
    Install the master cylinder (See Page 19-A-13).