Workshop manual

Front Brake Caliper

Disassembly/Reassembly

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF page 889 (manual page 19-A-12)

PDF p. 889 · 19-A-12

NOTE:

  • Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.
  • To prevent spills, cover the hose joints with rags or shop towels.
  • Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
  • Before reassembling, check that all parts are free of dust and other foreign particles.
  • Replace parts with new ones whenever specified to do so.
  • Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid.
  • Contaminated brake discs or pads reduce stopping ability.
  • When reusing the pads, always reinstall the brake pads in their original positions to prevent loss of braking efficiency.
  • Do not reuse the drained fluid.
  • Use only clean Genuine Honda brake fluid or an equivalent DOR3 or DOT4 brake fluid.
  • Coat the piston and caliper bore with clean brake fluid.
  • Replace all rubber parts with new ones whenever disassembled.
  • After installing the front brake caliper:
    • Check for leaks at hose and line joints and connections, and retighten if necessary.
    • Check the brake hoses for interference and twisting.
Illustration · Front Brake Caliper · Disassembly/Reassembly

Use recommended rubber grease in the caliper seal set.

Illustration · Front Brake Caliper · Disassembly/Reassembly

Use recommended seal grease in the caliper seal set.

Illustration: INNER SHIM B; INNER SHIM A; WEAR INDICATOR Install inner pad with its wear indicator upward; OUTER PAD SHIM; PIN B; PIN BOOT; PIN BOOTS, Replace; 12 mm FLANGE BOLTS, 113 Nm (11.5 kgf/m, 83 lbf/ft); CALIPER BRACKET; PAD RETAINERS; PIN A; BRAKE PADS; PAD SPRING; PISTON BOOT, Replace; PISTON; PISTON SEAL, Replace; CALIPER BODY; CALIPER BOLTS, 49 Nm (5.0 kgf/m, 36 lbf/ft); BLEED SCREW, 9 Nm (0.9 kgf/m, 7 lbf/ft); BRAKE HOSE; BANJO BOLT, 34 Nm (3.5 kgf/m, 25 lbf/ft); SEALING WASHERS, Replace
  1. 1. INNER SHIM B
  2. 2. INNER SHIM A
  3. 3. WEAR INDICATOR
    Install inner pad with its wear indicator upward
  4. 4. OUTER PAD SHIM
  5. 5. PIN B
  6. 6. PIN BOOT
  7. 7. PIN BOOTS, Replace
  8. 8. 12 mm FLANGE BOLTS, 113 Nm (11.5 kgf/m, 83 lbf/ft)
  9. 9. CALIPER BRACKET
  10. 10. PAD RETAINERS
  11. 11. PIN A
  12. 12. BRAKE PADS
  13. 13. PAD SPRING
  14. 14. PISTON BOOT, Replace
  15. 15. PISTON
  16. 16. PISTON SEAL, Replace
  17. 17. CALIPER BODY
  18. 18. CALIPER BOLTS, 49 Nm (5.0 kgf/m, 36 lbf/ft)
  19. 19. BLEED SCREW, 9 Nm (0.9 kgf/m, 7 lbf/ft)
  20. 20. BRAKE HOSE
  21. 21. BANJO BOLT, 34 Nm (3.5 kgf/m, 25 lbf/ft)
  22. 22. SEALING WASHERS, Replace