Workshop manual

Rear Spring/Bump Stop

Removal

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF page 875 (manual page 18-21)

PDF p. 875 · 18-21

  1. 1.
    Raise the rear of the vehicle and make sure it is securely supported. Remove the rear wheel.
  2. 2.
    Remove the flange bolt from the rear axle beam.
Illustration: REAR DAMPER; REAR AXLE BEAM; FLANGE BOLT, 10 x 1.25 mm
  1. 1. REAR DAMPER
  2. 2. REAR AXLE BEAM
  3. 3. FLANGE BOLT, 10 x 1.25 mm
  1. 3.
    Remove the 10 mm self-locking nut and separate the stabiliser link from the body.
  2. 4.
    Lower the floor jack gradually.
  3. 5.
    Remove the spring and upper spring seat.
  4. 6.
    Remove the flange nut that connects to the rear axle beam and remove the bump stop.
Illustration: BODY; STABILISER LINK; BUMP STOP; UPPER SPRING SEAT; SPRING; FLANGE NUT, 10 x 1.25 mm; SELF-LOCKING NUT, 10 x 1.25 mm. Replace.
  1. 1. BODY
  2. 2. STABILISER LINK
  3. 3. BUMP STOP
  4. 4. UPPER SPRING SEAT
  5. 5. SPRING
  6. 6. FLANGE NUT, 10 x 1.25 mm
  7. 7. SELF-LOCKING NUT, 10 x 1.25 mm. Replace.

Installation

  1. 1.
    Install the bump stop.
  2. 2.
    Install the spring and the upper spring seat.
  3. 3.
    Loosely install the stabiliser link to the body.
Illustration: BODY; STABILISER LINK; BUMP STOP; UPPER SPRING SEAT; SPRING; FLANGE NUT, 10 x 1.25 mm, 39 Nm (4.0 kgf/m, 29 lbf/ft); SELF-LOCKING NUT, 10 x 1.25 mm, Replace, 29 Nm (3.0 kgf/m, 22 lbf/ft)
  1. 1. BODY
  2. 2. STABILISER LINK
  3. 3. BUMP STOP
  4. 4. UPPER SPRING SEAT
  5. 5. SPRING
  6. 6. FLANGE NUT, 10 x 1.25 mm, 39 Nm (4.0 kgf/m, 29 lbf/ft)
  7. 7. SELF-LOCKING NUT, 10 x 1.25 mm, Replace, 29 Nm (3.0 kgf/m, 22 lbf/ft)
  1. 4.
    Loosely install the flange bolt to the rear axle beam.
  2. 5.
    Raise the rear axle beam with a floor jack until the vehicle just lifts off the safety stand.
Illustration: REAR DAMPER; FLANGE BOLT, 10 x 1.25 mm, 54 Nm (5.5 kgf/m, 40 lbf/ft)
  1. 1. REAR DAMPER
  2. 2. FLANGE BOLT, 10 x 1.25 mm, 54 Nm (5.5 kgf/m, 40 lbf/ft)
  1. 6.
    Tighten the self-locking nut.
  2. 7.
    Tighten the flange bolt
  3. 8.
    Install the rear wheel.