Workshop manual

Rear Wheel Bearing

Replacement

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 873, 874 (manual pages 18-19 to 18-20)

PDF p. 873 · 18-19

NOTE:

  • Use only genuine Honda wheel weights for aluminium wheels. No-genuine wheel weights may corrode and damage aluminium wheels.
  • Before installing the brake drum, clean the mating surfaces of the rear hub and the brake drum.
  • before install the wheel, clean the mating surfaces of the brake drum and inside the wheel.
Illustration: REAR AXLE BEAM; REAR WHEEL BEARING. Replace.; CIRCLIP; O-RING. Replace.; REAR BRAKE ASSEMBLY; 10 x 1.25 mm, 64 Nm (6.5 kgf/m, 64 lbf/ft); REAR HUB. Check for damage and cracks.; REAR WHEEL; WHEEL NUT, 12 x 1.5 mm, 108 Nm (11.0 kgf/m, 80 lbf/ft); HUB CAP. Replace; SPINDLE NUT, 22 x 1.5 mm, 196 Nm (20 kgf/m, 145 lbf/ft). NOTE: ♦ Before installing the spindle nut, apply engine oil to the seating surface; BRAKE DRUM. Check for wear and damage.; REAR BRAKE DRUM WASHER; .REAR HUB WASHER; COTTER PIN. Replace. of the nut.
  1. 1. REAR AXLE BEAM
  2. 2. REAR WHEEL BEARING. Replace.
  3. 3. CIRCLIP
  4. 4. O-RING. Replace.
  5. 5. REAR BRAKE ASSEMBLY
  6. 6. 10 x 1.25 mm, 64 Nm (6.5 kgf/m, 64 lbf/ft)
  7. 7. REAR HUB. Check for damage and cracks.
  8. 8. REAR WHEEL
  9. 9. WHEEL NUT, 12 x 1.5 mm, 108 Nm (11.0 kgf/m, 80 lbf/ft)
  10. 10. HUB CAP. Replace
  11. 11. SPINDLE NUT, 22 x 1.5 mm, 196 Nm (20 kgf/m, 145 lbf/ft).
    NOTE:
    ♦ Before installing the spindle nut, apply engine oil to the seating surface
  12. 12. BRAKE DRUM. Check for wear and damage.
  13. 13. REAR BRAKE DRUM WASHER
  14. 14. .REAR HUB WASHER
  15. 15. COTTER PIN. Replace. of the nut.

PDF p. 874 · 18-20

  1. 1.
    Loosen the wheel nuts slightly.
  2. 2.
    Raise the rear of the vehicle and support it with safety stands in the proper locations (see section 1).
  3. 3.
    Remove the wheel nuts and rear wheel.
Illustration: REAR BRAKE DRUM WASHER; REAR HUB WASHER; HUB CAP, Replace. NOTE: take care not to damage the hub unit on disassembly.; WHEEL NUT, 108 Nm (11 kgf/m, 80 lbf/ft); COTTER PIN, Replace, On reassembly, bend the cotter pin as shown.; SPINDLE NUT, 22 x 1.5 mm, 196 Nm (20 kgf/m, 145 lbf/ft) NOTE: Before installing the spindle nut, apply engine oil to the seating surface of the nut.
  1. 1. REAR BRAKE DRUM WASHER
  2. 2. REAR HUB WASHER
  3. 3. HUB CAP, Replace.
    NOTE: take care not to damage the hub unit on disassembly.
  4. 4. WHEEL NUT, 108 Nm (11 kgf/m, 80 lbf/ft)
  5. 5. COTTER PIN, Replace, On reassembly, bend the cotter pin as shown.
  6. 6. SPINDLE NUT, 22 x 1.5 mm, 196 Nm (20 kgf/m, 145 lbf/ft)
    NOTE: Before installing the spindle nut, apply engine oil to the seating surface of the nut.
  1. 4.
    Release the parking brake lever.
  2. 5.

    Screw two 8 x 1.25 mm bolts into the brake drum to push it away from the hub carrier.

    NOTE: Turn each bolt two turns at a time to prevent cocking the brake drum excessively.

  3. 6.
    Remove the brake drum, hub and circlip.
Illustration: 8 x 1.25 mm; BRAKE DRUM; REAR HUB; CIRCLIP
  1. 1. 8 x 1.25 mm
  2. 2. BRAKE DRUM
  3. 3. REAR HUB
  4. 4. CIRCLIP
  1. 7.
    Remove the rear driveshaft from the rear axle beam (see section 16).
  2. 8.
    Remove the rear wheel bearing from the axle beam.
Illustration: DRIVER, 07749 - 0010000; REAR AXLE BEAM; OUTSIDE; DRIVER ATTACHMENT, 42 x 47 mm, 07746 - 0010300
  1. 1. DRIVER, 07749 - 0010000
  2. 2. REAR AXLE BEAM
  3. 3. OUTSIDE
  4. 4. DRIVER ATTACHMENT, 42 x 47 mm, 07746 - 0010300
  1. 9.
    Install a new rear wheel bearing into the rear axle beam using the old bearing and a metal plate.
Illustration: REAR AXLE BEAM; OLD BEARING; METAL PLATE; OUTSIDE; NEW WHEEL BEARING
  1. 1. REAR AXLE BEAM
  2. 2. OLD BEARING
  3. 3. METAL PLATE
  4. 4. OUTSIDE
  5. 5. NEW WHEEL BEARING
  1. 10.
    Install in the reverse order of removal.
  2. 11.
    Check the rear wheel alignment (See Page 10-4).