PDF p. 1825 · 11-44
You can retrieve data from the ECM by connecting the scan tool or the Honda PGM Tester to the 16P data link connector (DLC). The items listed in the table below can be indicated by both the scan tool and Honda PGM Tester. The Honda PGM Tester also reads beyond these items. Understanding this data may help you find the causes of the intermittent problems.
NOTE:
- The “operating values” listed are approximate and may vary depending on the environment and the individual vehicle.
- Unless noted otherwise, “at idle speed” means idling with the engine completely warmed up, in neutral position, and the A/C and all accessories turned off.
| Data | Description | Operating Value | Freeze Data | ||||
|---|---|---|---|---|---|---|---|
| Diagnostic | If the ECM detects a problem, it will store it as a code | If no problem is | YES | ||||
| Trouble Code | consisting of one letter and four numbers. | detected, there is no | |||||
| (DTC) | output. | ||||||
| Engine Speed | The ECM computes engine speed from the signals | Nearly the same as | YES | ||||
| sent from the Crankshaft Position sensor. | tachometer indication | ||||||
| This data is used for determining the time and | At idle speed: | ||||||
| amount of fuel injection. | 750 + 50 rpm (min -1) | ||||||
| Vehicle Speed | The ECM converts pulse signals from the Vehicle | Nearly the same as | YES | ||||
| Speed Sensor (VSS) into speed data. | speedometer indication | ||||||
| Manifold | The absolute pressure caused in the intake manifold | With engine stopped: | YES | ||||
| Absolute | by engine load and speed. | Nearly the same as | |||||
| Pressure (MAP) | atmospheric pressure | ||||||
| At idle speed: | |||||||
| 28 - 44 kPa (210 - 310 | |||||||
| mmHg, 8.3 - 12.2 inHg) | |||||||
| Engine Coolant | The ECT sensor converts coolant temperature into | With cold engine: | YES | ||||
| Temperature | voltage and signals the ECM. | The sensor is a | Same as ambient | ||||
| (ECT) | thermistor whose internal resistance changes with | temperature and IAT | |||||
| coolant temperature. | The ECM uses the voltage | With engine warmed up: | |||||
| signals from the ECT sensor to determine the amount | approx. 78 - 100°C | ||||||
| of injected fuel. | (172 - 212°F) | ||||||
| Heated Oxygen | The Heated Oxygen Sensor detects the oxygen | 0.0 - 1.4 V | YES | ||||
| Sensor (HO2S) | content in the exhaust gas and sends voltage signals | At idle speed: | (Primary | ||||
| (Primary Sensor | to the ECM. | Based on these signals, the ECM | about 0.1 - 0.9 V | Sensor 1 | |||
| 1) | controls the air/fuel ratio. | When the oxygen content is | only) | ||||
| (Secondary | high (that is, when the ratio is leaner than the | ||||||
| Sensor 2) | stoichiometric ratio), the voltage signal is lower. | ||||||
| When the oxygen content is low (that is, when the | |||||||
| ratio is richer than the stoichiometric ratio), the | |||||||
| voltage signal is higher | |||||||
PDF p. 1826 · 11-45
| Data | Description | Operating Value | Freeze Data | ||||||
|---|---|---|---|---|---|---|---|---|---|
| HO2S Feedback | Loop status is indicated as “open” or “closed”. | At idle speed: closed | YES | ||||||
| Loop Status | Closed: Based on the HO2S output, the ECM | ||||||||
| determines the air/fuel ratio and controls the amount | |||||||||
| of injected fuel. | |||||||||
| Open: ignoring HO2S output, the ECM refers to | |||||||||
| signals from the TP, MAP and ECT sensors to control | |||||||||
| the amount of injected fuel. | |||||||||
| Short Term Fuel | The air/fuel ratio correction coefficient for correcting | + 20% | YES | ||||||
| Trim | the amount of injected fuel when HO2S feedback is in | ||||||||
| the closed loop status. | When the signal from the | ||||||||
| HO2S is weak, short term fuel trim gets higher, and | |||||||||
| the ECM increases the amount of injected fuel. | The | ||||||||
| air/fuel ratio gradually gets richer, causing a higher | |||||||||
| HO2S output. | Consequently, the short term fuel trim | ||||||||
| is lowered, and the ECM reduces the amount of | |||||||||
| injected fuel. | |||||||||
| This cycle keeps the air/fuel ratio close to the | |||||||||
| stoichiometric ratio when in closed loop status. | |||||||||
| Long Term Fuel | Long term fuel trim is computed from short term fuel | + 20% | YES | ||||||
| trim | trim and indicates changes occurring in the fuel | ||||||||
| supply system over a long period. | |||||||||
| If long term fuel trim is higher than 1.00, the amount | |||||||||
| of injected fuel must be increased. | If it is lower than | ||||||||
| 1.00, the amount of injected fuel must be reduced. | |||||||||
| Intake Air | The IAT sensor converts intake air temperature into | With cold engine: | YES | ||||||
| Temperature | voltage and signals the ECM. | When intake air | Same as ambient | ||||||
| (IAT) | temperature is low, the internal resistance of the | temperature and ECT | |||||||
| sensor increases, and the voltage signal is higher. | |||||||||
| Throttle Position | Based on the accelerator pedal position, the opening | At idle speed: | YES | ||||||
| angle of the throttle valve is indicated. | approx. 10% | ||||||||
| Ignition Timing | Ignition timing is the ignition advance angle set by the | At idle speed: | YES | ||||||
| ECM. | The ECM matches ignition timing to the driving | 12° + 2° | |||||||
| conditions. | BTDC with the SCS | ||||||||
| short connector | |||||||||
| connected | |||||||||
| Calculated Load | CLV is the engine load calculated from the MAP data. | At idle speed: | YES | ||||||
| Valve (CLV) | 15 - 35% | ||||||||
| At 2,500 rpm with no | |||||||||
| load: | |||||||||
| 12 - 30% | |||||||||