Workshop manual

General Troubleshooting Information

ECM/PCM Terminal Arrangement

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF pages 1827, 1828, 1829, 1830 (manual pages 11-46 to 11-49)

PDF p. 1827 · 11-46

ECM/PCM Connector A (32P)

Illustration: NOTE: Standard battery voltage is 12 V.

NOTE: Standard battery voltage is 12 V.

TerminalWireTerminal nameDescriptionSignal
numbercolour
6REDPCS (EVAP PURGEDrives EVAP purgeWith engine running, engine coolant below
CONTROL SOLENOIDcontrol solenoid valve.68°C (154°F): battery voltage
VALVE)With engine running, engine coolant
above 68°C (154°F): duty controlled
7*1GRNATPD (AT GEARDetects A/T gearIn D position: 0 V
POSITION SWITCH)position switch signal.In any other position: about 5 V
8BLK/WHTSHO2SHTCDrives secondaryWith ignition switch ON (II): battery voltage
(SECONDARYheated oxygenWith fully warmed up engine running: duty
HEATED OXYGENsensor heater.controlled.
SENSOR HEATER
CONTROL)
9*1LT GRNATPNP (AT GEARDetects A/T gearIn N or P position: 0 V
POSITION SWITCH)position switch signal.In any other position: battery voltage
10BRNSCS (SERVICEDetects serviceWith the terminal connected: 0 V
CHECK SIGNAL)check connectorWith the terminal disconnected: about 5 V
signal (the signalor battery voltage
causing a DTC
indication)
12PNKIMOLMPDrives immobiliserWith immobiliser indicator light turned ON:
(IMMOBILISERindicator light.0 V
INDICATOR LIGHT)With immobiliser indicator light turned
OFF: battery voltage
13BLUIMOENSends immobiliser
(IMMOBILISERenable signal.
ENABLE SIGNAL)
15GRN/YELFLR (FUEL PUMP0 V for two seconds0 V for two seconds after turning ignition
RELAY)after turning ignitionswitch ON (II), then battery voltage
switch ON (II), then
battery voltage
17BLK/REDACC (A/C CLUTCHDrives A/C clutchWith compressor ON: 0 V
RELAY)relay.With compressor OFF: battery voltage
18GRN/ORNMIL (MALFUNCTIONDrives MIL.With MIL turned ON: 0 V
INDICATOR LIGHT)With MIL turned OFF: battery voltage
19BLU/BLKNEP (ENGINE SPEEDOutputs engineWith engine running: pulses
PULSE)speed pulse.
20GRNFANC (RADIATORDrives radiator fanWith radiator fan running: 0 V
FAN CONTROL)relay.With radiator fan stopped: battery voltage
21LT BLUK-LINE (DLC)Sends and receivesWith ignition switch ON (II): battery voltage
scan tool signal.
22*1BLUATPL (AT GEARDetects A/T gearIn L position: 0 V
POSITION SWITCH)position switch signal.In any other position: battery voltage
23*3WHT/REDSHO2S (SECONDARYDetects secondaryWith throttle fully opened from idle with
HEATED OXYGENheated oxygenfully warmed up engine: above 0.6 V
SENSOR, SENSOR 2)sensor (sensor 2)With throttle quickly closed: below 0.4 V
signal.
24BLU/WHTSTS (STARTERDetects starter switchWith starter switch ON (III): battery voltage
SWITCH SIGNAL)signal.With starter switch OFF: 0 V
25REDIMOCDDetects immobiliser
(IMMOBILISER CODE)signal.
26GRNPSPSW (P/SDetects PSP switchAt idle with steering wheel in straight
PRESSURE SWITCHsignal.ahead position: 0 V
SIGNAL)At idle with steering wheel at full lock:
battery voltage
27BLU/REDACS (A/C SWITCHDetects A/C switchWith A/C switch ON: 0 V
SIGNALsignal.With A/C switch OFF: battery voltage
30*1GRN/REDELDDetects ELD signal.With parking lights turned on at idle: about
2.5 - 3.5 V
With low beam headlights turned on at
idle: about 1.5 - 2.5 V
32GRN/WHTBKSW (BRAKEDetects brake switchWith brake pedal released: 0 V
SWITCH)signal.With brake pedal depressed: battery
voltage
  • *1:
    A/T
  • *2:
    D16W5 engine
  • *3:
    D16W1 engine

PDF p. 1828 · 11-47

ECM/PCM Connector B (25P)

Illustration: NOTE: Standard battery voltage is 12 V.

NOTE: Standard battery voltage is 12 V.

TerminalWireTerminal nameDescriptionSignal
numbercolour
1YEL/BLKIGP1 (POWERPower source for theWith ignition switch ON (II): battery voltage
SOURCE)ECM/PCM controlWith ignition switch OFF: 0 V
circuit.
2BLKPG1 (POWERGround for theLess than 1.0 V at all times
GROUND)ECM/PCM control
circuit.
3REDINJ2 (No. 2 FUELDrives No. 2 fuelWith engine running: duty controlled
INJECTOR)injector.
4BLUINJ3 (No. 3 FUELDrives No. 3 fuelWith engine running: duty controlled
INJECTOR)injector.
5YELINJ4 (No. 4 FUELDrives No. 4 fuelWith engine running: duty controlled
INJECTOR)injector.
6*3BLK/BLUIACVP (IDLE AIRDrives IAC valveWith engine running: duty controlled
CONTROL VALVE(positive side).
POSITIVE SIDE)
8*1RED/BLKHLCLSM (PH-PLPH-PL control linearWith ignition switch ON (II): duty controlled
CONTROL LINEARsolenoid power
SOLENOID M SIDE)supply negative
electrode
9YEL/BLKIGP2 (POWERPower source for theWith ignition switch ON (II): battery voltage
SOURCE)ECM/PCM controlWith ignition switch OFF: 0 V
circuit.
10BLKPG2 (POWERGround for theLess than 1.0 V at all times
GROUND)ECM/PCM control
circuit.
11BRNINJ1 (No. 1 FUELDrives No. 1 fuelWith engine running: duty controlled
INJECTOR)injector.
12GRN/YELVTS (VTECDrives VTECWith engine at low rpm: 0 V
SOLENOID VALVE)solenoid valve.With engine at high rpm (vehicle running):
battery voltage
13YEL/GRNICM (IGNITIONSends ignition pulse.With ignition switch ON (II): battery voltage
CONTROL MODULE)With engine running: pulses
15*3ORNIACVN (IDLE AIRDrives IAC valveWith engine running: duty controlled
CONTROL VALVE(negative side).
NEGATIVE SIDE
17*1GRN/WHTHLCLSP (PH-PLPH-PL control linearWith ignition switch ON (II): duty controlled
CONTROL LINEARsolenoid power
SOLENOID P SIDE)supply positive
electrode.
18*1RED/BLUSCLSM (STARTStart clutch controlWith ignition switch ON (II): duty controlled
CLUTCH CONTROLlinear solenoid power
LINEAR SOLENOID Msupply negative
SIDE)electrode.
20BRN/BLKLG1 (LOGICGround for theLess than 1.0 V at all times
GROUND)ECM/PCM control
circuit.
21WHT/BLUVBU (VOLTAGE BACKPower source for theBattery voltage at all times
UP)ECM/PCM control
circuit.Power source
for the DTC memory.
22BRN/BLKLG2 (LOGICGround for theLess than 1.0 V at all times
GROUND)ECM/PCM control
circuit.
23*2BLK/BLUIACV (IDLE AIRDrives IAC valve.With engine running: pulses
CONTROL VALVE)
25*1YELSCLSP (STARTStart clutch controlWith ignition switch ON (II): duty controlled
CLUTCH CONTROLlinear solenoid power
LINEAR SOLENOID Psupply positive
SIDE)electrode.
  • *1:
    A/T
  • *2:
    D16W5 engine
  • *3:
    D16W1 engine

PDF p. 1829 · 11-48

ECM/PCM Connector C (31P)

Illustration: NOTE: Standard battery voltage is 12 V.

NOTE: Standard battery voltage is 12 V.

TerminalWireTerminal nameDescriptionSignal
numbercolour
1BLK/WHTPO2SHTC (PRIMARYDrives primaryWith ignition switch ON (II): battery voltage
HEATED OXYGENheated oxygenWith fully warmed up engine running: duty
SENSOR HEATERsensor heater.controlled
CONTROL)
2WHT/GRNALTC (ALTERNATORSends alternatorWith fully warmed-up engine running:
CONTROL)control signal.battery voltage
During driving with small electrical load: 0
V
3*2RED/BLUKS (KNOCK SENSOR)Detects KS signal.With engine knocking: pulses
5WHT/REDALTF (ALTERNATORDetects alternator FRWith fully warmed-up engine running: 0 V -
FR SIGNAL)signal.battery voltage (depending on electrical
load)
7GRN/WHTSG1 (SENSORGround for MAPLess than 1.0 V at all times
GROUND)sensor.
8BLUCKPP (CKP SENSORDetects CKP sensor.With engine running: pulses
P SIDE)
9WHTCKPM (CKP SENSORGround for CKP
M SIDE)sensor.
10*2BLU/BLKVTM (VTECDetects VTECWith engine at low engine speed: 0 V
PRESSURE SWITCH)pressure switchWith engine at high engine speed: battery
signal.voltage.
12BLK/WHTEGT (EXHAUST GASDetects EGT sensorWith ignition switch ON (II): about 0.1 - 4.8
TEMPERATUREsignal.V (depending on exhaust gas temperature)
SENSOR)
16WHTPHO2S (PRIMARYDetects primaryWith throttle fully opened from idle with
HEATED OXYGENheated oxygenfully warmed up engine: above 0.6 V
SENSOR, SENSOR 1)sensor (sensor 1)With throttle quickly closed: below 0.4 V
signal.
17RED/GRNMAP (MANIFOLDDetects MAP sensorWith ignition switch ON (II): about 3 V
ABSOLUTEsignal.At idle: about 1.0 V (depending on engine
PRESSURE SENSOR)speed)
18GRN/BLKSG2 (SENSORSensor ground.Less than 1.0 V at all times
GROUND)
19YEL/REDVCC1 (SENSORPower source to MAPWith ignition switch ON (II): about 5 V
VOLTAGE)sensor.With ignition switch OFF: 0 V
20GRNTDCP (TDC SENSORDetects TDC sensor.With engine running: pulses
P SIDE)
21REDTDCM (TDC SENSORGround for TDC
M SIDE)sensor.
22BLU/REDCKFP (CKF SENSORDetects CKF sensor.With engine running: pulses
P SIDE)
23BLU/WHTVSS (VEHICLEDetects VSS signal.With ignition switch ON (II) and front wheel
SPEED SENSOR)rotating: cycles 0 V - 5 V
25RED/YELIAT (INTAKE AIRDetects IAT sensorWith ignition switch ON (II): about 0.1 - 4.8
TEMPERATUREsignal.V (depending on intake air temperature)
SENSOR)
26RED/WHTECT (ENGINEDetects ECT sensorWith ignition switch ON (II): about 0.1 - 4.8
COOLANTsignal.V (depending on engine coolant
TEMPERATUREtemperature)
SENSOR)
27RED/BLKTPS (THROTTLEDetects TP sensorWith throttle fully open: 4.8 V
POSITION SENSOR)signal.With throttle fully closed: about 0.5 V
28YEL/BLUVCC2 (SENSORProvides sensorWith ignition switch ON (II): about 5 V
VOLTAGE)voltage.With ignition switch OFF: 0 V
29YELCYPP (CYP SENSORDetects CYP sensor.With engine running: pulses
P SIDE)
30BLKCYPM (CYP SENSORGround for CYP
M SIDE)sensor.
31WHT/REDCKFM (CKF SENSORGround for CKF
M SIDE)sensor signal.
  • *1:
    A/T
  • *2:
    D16W5 engine
  • *3:
    D16W1 engine

PDF p. 1830 · 11-49

PCM Connector D (16P)*4

Illustration: NOTE: Standard battery voltage is 12 V.

NOTE: Standard battery voltage is 12 V.

TerminalWireTerminal nameDescriptionSignal
numbercolour
1*1WHT/REDVEL (SECONDARYSecondary gear shaftDepending on vehicle speed: pulses
GEAR SHAFT SPEEDspeed sensor.When vehicle is stopped: 0 V
SENSOR)
2*1GRNINHSOL (INHIBITORInhibitor solenoidWith inhibitor solenoid ON: battery voltage
SOLENOIDcontrol.With inhibitor solenoid OFF: 0 V
CONTROL)
3*1GRN/YELSHLS M (SHIFTShift control linearWith ignition switch ON (II): pulses
CONTROL LINEARsolenoid power
SOLENOID M SIDE)supply negative
electrode.
4*1BLU/WHTSHLS P (SHIFTShift control linearWith ignition switch ON (II): pulses
CONTROL LINEARsolenoid power
SOLENOID P SIDE)supply positive
electrode.
5*1BLK/YELVBSOL (BATTERYPower source ofWith ignition switch ON (II): battery voltage
VOLTAGE FORsolenoid valve.With ignition switch OFF: 0 V
SOLENOID VALVE)
6*1WHTATPR (AT GEARDetects A/T gearIn R position: 0 V
POSITION SWITCH)position switch signal.In any other position: battery voltage
7*1BLK/WHTVELSG (SECONDARYGround for secondary
GEAR SHAFT SPEEDgear shaft speed
SENSOR GROUND)sensor.
8*1LT GRNSPOIND (SDrives S indicator.With S indicator turned ON: battery
INDICATOR LIGHT)voltage
With S indicator turned OFF: 0 V
9*1BLUDSW (D MODEDetects D modeWith D mode switch ON: 0 V
SWITCH)switch signal.With D mode switch OFF: battery voltage
10*1WHTNDN (DRIVENDetects driven pulleyIn other than N or P positions: pulses
PULLEY SPEEDspeed sensor signal.
SENSOR)
11*1RED/BLUNDR (DRIVE PULLEYDetects drive pulleyIn other than N or P position: pulses
SPEED SENSOR)speed sensor signal.
12*1GRNNDRSG (DRIVEGround for drive
PULLEY SPEEDpulley speed sensor.
SENSOR GROUND)
13*1YELSPOSW (S MODEDetects S modeWith S mode switch ON: 0 V
SWITCH)switch signal.With S mode switch OFF: battery
voltage
14*1GRN/BLKDIND (D INDICATORDrives D indicator.With D indicator turned ON: battery
LIGHT)voltage
With D indicator turned OFF: 0 V
16*1RED/WHTNDNSG (DRIVENGround for driven
PULLEY SPEEDpulley speed sensor.
SENSOR GROUND)
  • *1:
    A/T