Workshop manual

Cylinder Head

Illustrated Index

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 251, 252 (manual pages 6-12 to 6-13)

PDF p. 251 · 6-12

NOTE:

  • To avoid damage, wait until the engine coolant temperature drops below 38°C (100°F) before removing the cylinder head.
  • When handling a metal gasket, take care not to fold it or damage the contact surface.
  • Use new O-rings and gaskets when reassembling.
Illustration: CYLINDER HEAD COVER, (See Page 6-30) when installing cylinder head cover.; WASHER, Replace when damaged or deteriorated.; 6 x 10, 9.8 Nm (1.0 kgf/m, 7.2 lbf/ft). Apply soapsuds to threads and cylinder head contact surface when replacing the rubber seal, then remove any soapsuds after installing rubber seal.; RUBBER SEAL. Replace when damaged or deteriorated.; CYLINDER HEAD BOLT, 10 x 1.25 mm, 67 Nm (6.8 kgf/m, 49 lbf/ft) Tightening (See Page 6-30). Apply engine oil to the threads.; CYLINDER HEAD; CYLINDER HEAD GASKET, Replace.; DOWEL PIN 9 O-RING, Replace.; 8 x 1.25 mm, 24 Nm (2.4 kgf/m, 17 lbf/ft); DISTRIBUTOR; HEAD COVER GASKET, Replace when leaking, damaged or deteriorated. Apply liquid gasket at four corners of the recesses.
  1. 1. CYLINDER HEAD COVER,
    (See Page 6-30) when installing cylinder head cover.
  2. 2. WASHER, Replace when damaged or deteriorated.
  3. 3. 6 x 10, 9.8 Nm (1.0 kgf/m, 7.2 lbf/ft). Apply soapsuds to threads and cylinder head contact surface when replacing the rubber seal, then remove any soapsuds after installing rubber seal.
  4. 4. RUBBER SEAL. Replace when damaged or deteriorated.
  5. 5. CYLINDER HEAD BOLT, 10 x 1.25 mm, 67 Nm (6.8 kgf/m, 49 lbf/ft) Tightening (See Page 6-30). Apply engine oil to the threads.
  6. 6. CYLINDER HEAD
  7. 7. CYLINDER HEAD GASKET, Replace.
  8. 8. DOWEL PIN
    9 O-RING, Replace.
  9. 10. 8 x 1.25 mm, 24 Nm (2.4 kgf/m, 17 lbf/ft)
  10. 11. DISTRIBUTOR
  11. 12. HEAD COVER GASKET,
    Replace when leaking, damaged or deteriorated. Apply liquid gasket at four corners of the recesses.

PDF p. 252 · 6-13

OIL Prior to reassembling, clean all the parts in solvent, dry them, and apply lubricant to any contact parts.

Illustration: ROCKER ARM ASSEMBLY Removal (See Page 6-18) Inspection (See Page 6-19).; 8 x 1.25 mm, 20 Nm (2.0 kgf/m, 14 lbf/ft). Apply engine oil to the threads.; 6 x 1.0 mm, 12 Nm (1.2 kgf/m, 8.7 lbf/ft); VALVE KEEPERS; SPRING RETAINER; INTAKE VALVE SPRING; INTAKE VALVE SEAL , Replace.; VALVE SPRING SEAT; INTAKE VALVE GUIDE; CAMSHAFT PULLEY; 8 x 1.25 mm, 37 Nm (3.8 kgf/m, 27 lbf/ft), Apply engine oil to the threads.; OIL SEAL, Replace.; CYLINDER HEAD Removal, (See Page 6-14). Warpage, (See Page 6-24). Valve seat reconditioning, (See Page 6-25). Installation, (See Page 6-29).; EXHAUST VALVE; INTAKE VALVE Removal, (See Page 6-23) Installation, (See Page 6-27); EXHAUST VALVE GUIDE Inspection, (See Page 6-24). Replacement, (See Page 6-26). Reaming, (See Page 6-26).; VALVE SPRING SEAT; EXHAUST VALVE SEAL , Replace.; EXHAUST VALVE SPRING; SPRING RETAINER; VALVE KEEPERS; O-RING, Replace.; OIL CONTROL ORIFICE, Clean.; CAMSHAFT Inspection, (See Page 6-21)
  1. 1. ROCKER ARM ASSEMBLY Removal (See Page 6-18) Inspection (See Page 6-19).
  2. 2. 8 x 1.25 mm, 20 Nm (2.0 kgf/m, 14 lbf/ft).
    Apply engine oil to the threads.
  3. 3. 6 x 1.0 mm, 12 Nm (1.2 kgf/m, 8.7 lbf/ft)
  4. 4. VALVE KEEPERS
  5. 5. SPRING RETAINER
  6. 6. INTAKE VALVE SPRING
  7. 7. INTAKE VALVE SEAL , Replace.
  8. 8. VALVE SPRING SEAT
  9. 9. INTAKE VALVE GUIDE
  10. 10. CAMSHAFT PULLEY
  11. 11. 8 x 1.25 mm, 37 Nm (3.8 kgf/m, 27 lbf/ft),
    Apply engine oil to the threads.
  12. 12. OIL SEAL, Replace.
  13. 13. CYLINDER HEAD
    Removal, (See Page 6-14). Warpage, (See Page 6-24).
    Valve seat reconditioning, (See Page 6-25).
    Installation, (See Page 6-29).
  14. 14. EXHAUST VALVE
  15. 15. INTAKE VALVE
    Removal, (See Page 6-23) Installation, (See Page 6-27)
  16. 16. EXHAUST VALVE GUIDE Inspection, (See Page 6-24). Replacement, (See Page 6-26). Reaming, (See Page 6-26).
  17. 17. VALVE SPRING SEAT
  18. 18. EXHAUST VALVE SEAL , Replace.
  19. 19. EXHAUST VALVE SPRING
  20. 20. SPRING RETAINER
  21. 21. VALVE KEEPERS
  22. 22. O-RING, Replace.
  23. 23. OIL CONTROL ORIFICE, Clean.
  24. 24. CAMSHAFT
    Inspection, (See Page 6-21)