Workshop manual

Seat Belts

Rear Seat Belt Replacement

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1271, 1272 (manual pages 24-6 to 24-7)

PDF p. 1271 · 24-6

Check the rear seat belts for damage and replace them if necessary. Be careful not to damage them during removal and installation.

Rear seat belt:

  1. 1.
    Slide the front seat forward fully.
  2. 2.
    Remove (see section 20):
    • Rear seat-backs
    • Rear seat cushion
    • Side trim
    • Rear side trim panel
  3. 3.
    Remove the lower anchor bolt, then remove the retractor bolt and retractor mounting bolt. remove the rear seat belt and retractor.
Illustration: RETRACTOR BOLT, 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft); RETRACTOR MOUNTING BOLT; RETRACTOR; LOWER ANCHOR BOLT, 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft); REAR SEAT BELT
  1. 1. RETRACTOR BOLT, 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft)
  2. 2. RETRACTOR MOUNTING BOLT
  3. 3. RETRACTOR
  4. 4. LOWER ANCHOR BOLT, 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft)
  5. 5. REAR SEAT BELT
  1. 4.
    Install in the reverse order of removal and note the following items:
    • Check that the retractor locking mechanism functions (See Page 24-8).
    • Assemble the washers, collar and bushing on the upper and lower anchor bolts as shown.
    • Before installing the anchor bolts, make sure there are no twists or kinks in the front seat belt.

Lower anchor bolt construction:

Illustration: LOWER ANCHOR BOLT; LOWER ANCHOR; TOOTHED LOCK WASHER
  1. 1. LOWER ANCHOR BOLT
  2. 2. LOWER ANCHOR
  3. 3. TOOTHED LOCK WASHER

Retractor bolt construction:

Illustration: RETRACTOR BOLT; RETRACTOR; TOOTHED LOCK WASHER
  1. 1. RETRACTOR BOLT
  2. 2. RETRACTOR
  3. 3. TOOTHED LOCK WASHER

PDF p. 1272 · 24-7

Centre belt and seat belt buckles:

  1. 1.
    Slide the front seat forward fully.
  2. 2.
    Remove the rear seat-backs and rear seat cushion (see section 20).
  3. 3.
    Remove the centre anchor bolts and remove the seat belt buckles.
Illustration: REAR SEAT BELT BUCKLE; CENTRE ANCHOR BOLTS 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft); REAR SEAT BELT BUCKLE; CENTRE BELT BUCKLE, For some models; CENTRE BELT, For some models
  1. 1. REAR SEAT BELT BUCKLE
  2. 2. CENTRE ANCHOR BOLTS 7/16-20 UNF, 32 Nm (3.3 kgf/m, 24 lbf/ft)
  3. 3. REAR SEAT BELT BUCKLE
  4. 4. CENTRE BELT BUCKLE, For some models
  5. 5. CENTRE BELT, For some models

Rear seat belt buckle construction:

Illustration: CENTRE ANCHOR BOLT; CENTRE ANCHOR; TOOTHED LOCK WASHER
  1. 1. CENTRE ANCHOR BOLT
  2. 2. CENTRE ANCHOR
  3. 3. TOOTHED LOCK WASHER
  1. 4.
    Install in the reverse order of removal and note the following items:
    • Check that the retractor locking mechanism functions (See Page 24-8).
    • Assemble the washers on the centre anchor bolt as shown.
    • Before installing the centre anchor bolt, make sure there are no twists or kinks in the centre belt.