Workshop manual

Power Mirrors

Function Test (4D)

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF page 2048 (manual page 23-F-6)

PDF p. 2048 · 23-F-6

  1. 1.
    Remove the switch panel from the dashboard.
  2. 2.
    Disconnect the 10P connector from the power mirror switch.
  3. 3.
    Push the switch out from behind the switch panel.
Illustration: 10P CONNECTOR; POWER MIRROR SWITCH; Wire side of female terminals
  1. 1. 10P CONNECTOR
  2. 2. POWER MIRROR SWITCH
  3. 3. Wire side of female terminals
  • *1:
    With defogger
  • *2:
    With retractable power mirror

Mirror Test

Both inoperative:

  1. 1.

    Check for voltage between the No. 1 terminal and body ground with the ignition switch ON (II).

    There should be battery voltage.

    • If there is no battery voltage, check for:
      • blown No. 11 (7.5 A) fuse in the under-dash fuse/relay box.
      • an open in the BLK/YEL wire.
    • If there is battery voltage, go to step 2.
  2. 2.

    Check for continuity between the No. 2 terminal and body ground.

    There should be continuity.

    • If there is no continuity, check for:
      • an open in the BLK wire.
      • poor ground (G401, G402)
    • If there is continuity, check both mirrors individually as described in the next column.

Left mirror inoperative:

Connect the No. 1 terminal to the No. 7 terminal, and the No. 4 (or No. 9) terminal to body ground with jumper wires. The left mirror should tilt down (or swing left) with the ignition switch ON (II).

  • If the mirror does not tilt down (or does not swing left), check for an open in the No. 4 (or No. 9) terminal wire between the left mirror and the 10P connector. If the wire is OK, check the left mirror actuator.
  • If the mirror neither tilts down nor swings left, repair the No. 7 terminal wire.
  • If the mirror works properly, check the mirror switch.

Right mirror inoperative:

Connect the No. 1 terminal to the No. 8 terminal, and the No. 4 (or No. 10) terminal to body ground with jumper wires. The right mirror should tilt down (or swing left) with the ignition switch ON (II).

  • If the mirror does not tilt down (or does not swing left), check for an open in the No. 4 (or No. 10) terminal wire between the right mirror and the 10P connector. If the wire is OK, check the right mirror actuator.
  • If the mirror neither tilts down nor swings left, repair the No. 8 terminal wire.
  • If the mirror works properly, check the mirror switch.

Defogger test:

Connect the No. 3 and No. 6 terminals with a jumper wire, and check for voltage between the No. 3 terminal and body ground. There should be battery voltage and both mirrors should warm up with the ignition switch ON (II).

  • If there is no voltage or neither warms up, check for:
    • an open in the BLK/YEL and BLU/YEL wires.
    • blown No. 11 (7.5 A) in the under-dash fuse/relay box.
    • poor ground (G401, G402)
  • If only one fails to warm up, check its defogger.
  • If both fail to warm up, check the defogger switch. Retractable mirror inoperative:

Connect the No. 1 (BLK/YEL) terminal of the 10P connector to the No. 6 (GRN/ORN) terminal and the No. 5 (GRN/YEL) terminal to body ground with jumper wires. The mirrors should extend when the ignition switch is turned ON (II).

Connect the No. 1 (BLK/YEL) terminal of the 10P connector to the No. 5 (GRN/YEL) terminal and the No. 6 (GRN/ORN) terminal to body ground with jumper wires. The mirrors should retract when the ignition switch is turned ON (II).

  • If one of the mirrors does not retract or extend, check the retractable mirror actuator.
  • If the mirrors operate properly, replace the switch.