Workshop manual

Power Windows

Master Switch Input Test (4D)

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF pages 2032, 2033, 2034 (manual pages 23-E-6 to 23-E-8)

PDF p. 2032 · 23-E-6

NOTE: The control unit is built into the power window master switch, and only controls driver’s door window operations.

  1. 1.
    Remove the power window master switch and armrest pocket from the door panel.
  2. 2.
    Disconnect the 14P and 7P connectors from the power window master switch.
  3. 3.
    Inspect the connector and socket terminals to be sure they are all making good contact.
    • If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
    • If the terminals look OK, make the following input tests at the connector.
      • If a test indicates a problem, find and correct the cause, then recheck the system.
      • If all the input tests prove OK, the power window master switch must be faulty; replace it.
Illustration: 7P CONNECTOR; POWER WINDOW MASTER SWITCH; 14P CONNECTOR; LHD type; RHD type; Wire side of female terminals
  1. 1. 7P CONNECTOR
  2. 2. POWER WINDOW MASTER SWITCH
  3. 3. 14P CONNECTOR
  4. 4. LHD type
  5. 5. RHD type
  6. 6. Wire side of female terminals

PDF p. 2033 · 23-E-7

Disconnect the connector to the power window master switch.

CavityWireTest conditionTest: Desired resultPossible cause if result is
not obtained
A38BLU/BLKUnder all conditionsCheck for voltage to ground:♦Blown No. 52 (20 A) fuse in
[A13]There should be battery voltage.the under-hood fuse/relay
box
♦An open in the wire
A2YEL/BLKIgnition Switch ON (II)Check for voltage to ground:♦Blown No. 4 (10 A) fuse in
[A5]There should be battery voltage.the under-dash fuse/relay
box
♦An open in the wire
A14GRN/BLKIgnition Switch ON (II)Check for voltage to ground:♦Blown No. 14, 15 and 16
[A7]There should be battery voltage.(20 A) fuse in the
under-dash fuse/relay box
♦Faulty power window relay
♦An open in the wire
B5YEL/REDIgnition Switch ON (II)Check for voltage to ground:♦Blown No. 14, 15 and 16
There should be battery voltage.(20 A) fuse in the
under-dash fuse/relay box
♦Faulty power window relay
♦An open in the wire
B6YEL/BLKIgnition Switch ON (II)Check for voltage to ground:♦Blown No. 14, 15 and 16
There should be battery voltage.(20 A) fuse in the
under-dash fuse/relay box
♦Faulty power window relay
♦An open in the wire
A12BLKUnder all conditionsCheck for continuity to ground:♦Poor ground (G401, G402)
[A9]There should be continuity.♦An open in the wire
B2BLKUnder all conditionsCheck for continuity to ground:♦Poor ground (G401, G402)
There should be continuity:♦An open in the wire
A5BLU/YELConnect the A13 [A8]Check for front passenger’s♦Faulty front passenger’s
[A2]terminal to the A14window motor:window motor
[A7] terminal, and theIt should run. (the window moves♦Faulty front passenger’s
A5 [A2] terminal to thedown)window switch
A12 [A9] terminal.♦An open in the wire
A13BLU/ORNConnect the A13 [A8}Check for front passenger’s♦Faulty front passenger’s
[A8]terminal to the A14window motor:window motor
[A7] terminal, and theIt should run. (the window moves♦Faulty front passenger’s
A5 [A2] terminal to thedown)window switch
A12 [A9] terminal.♦An open in the wire
B1BRN/WHTConnect the B4Check for left rear window motor.♦Faulty left rear window motor
terminal to the B5It should run. (the window moves♦Faulty left rear window
terminal, and the B1down)switch
terminal to the B2♦An open in the wire
terminal.
B4BRNConnect the B4Check for left rear window motor.♦Faulty left rear window motor
terminal to the B5It should run. (the window moves♦Faulty left rear window
terminal, and the B1down)switch
terminal to the B2♦An open in the wire
terminal.
B3BLU/ORNConnect the B7Check for right rear window♦Faulty right rear window
terminal to the B6motor.motor
terminal, and the B3It should run. (the window moves♦Faulty right rear window
terminal to the B2down)switch
terminal.♦An open in the wire
B7BRN/YELConnect the B7Check for right rear window♦Faulty right rear window
terminal to the B6motor.motor
terminal, and the B3It should run. (the window moves♦Faulty right rear window
terminal to the B2down)switch
terminal.♦An open in the wire
A1RED/BLUConnect the A7 [A14]Check for driver’s window motor.♦Faulty driver’s power
[A6]terminal to the A8It should run. (the window moveswindow motor
[A13] terminal, and thedown)♦An open in the wire
A1 [A6] terminal to the
A12 [A9] terminal.
A7RED/YELConnect the A7 [A14]Check for driver’s window motor.♦Faulty driver’s power
[A14]terminal to the A8It should run. (the window moveswindow motor
[A13] terminal, and thedown)♦An open in the wire
A1 [A6] terminal to the
A12 [A9] terminal.

[ ]: RHD type

PDF p. 2034 · 23-E-8

LHD type:

Illustration: RHD type:

RHD type:

Illustration: COMMON:

COMMON:

Illustration · LHD type

Reconnect the connector to the power window master switch.

CavityWireTest conditionTest: Desired resultPossible cause if result is
not obtained
A9WHTIgnition switch ON (II)Check for voltage to ground:♦Faulty power window
[A12]There should be battery voltage.master switch
♦An open in the wire
A3BLKUnder all conditionsCheck for continuity to ground:♦Faulty power window
[A4]There should be continuity.master switch
♦An open in the wire
A11BLUIgnition switch ON (II),Check for voltage between the♦Faulty driver’s window motor
[A10]and the driver’sA11 [A10] and A12 [A9]♦Faulty power window
window switch AUTOterminals:master switch
UP.There should be 0 - 5 V or more♦An open in the wire
repeatedly.
A10YELIgnition switch ON (II),Check for voltage between the♦Faulty driver’s window motor
[A11]and the driver’sA10 [A11] and A12 [A9]♦Faulty power window
window switch AUTOterminals:master switch
DOWN.There should be 0 - 5 V or more♦An open in the wire
repeatedly.

[ ]: RHD type