Workshop manual

Glass

Quarter Glass Replacement

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 966, 967, 968, 969 (manual pages 20-30 to 20-33)

PDF p. 966 · 20-30

NOTE:

  • Wear gloves to remove and install the quarter glass.
  • Use seat covers to avoid damaging any surface.
  • Use glass adhesive set P/N, 08C73-X0230N.
  1. 1.
    Remove:
    • Rear side shelf (See Page 20-41).
    • Upper portion of rear side trim (See Page 20-41).
    • Centre pillar trim (See Page 20-41).
    • Rear pillar trim (See Page 20-41).
    • Taillight (see section 23)
  2. 2.
    Pull down the rear side portion of the headliner (See Page 20-41). Take care not to bend the headliner excessively, or you may crease or break it.
  3. 3.

    Remove the quarter glass front trim and quarter glass rear trim.

    NOTE: Replace the quarter glass front trim and quarter glass rear trim.

  4. 4.

    From inside or outside the vehicle, with a knife to cut through the quarter glass adhesive all the way around.

    NOTE: Apply protective tape along the edge of the entire quarter glass opening flange.

  5. 5.
    Carefully remove the quarter glass.
  6. 6.
    With a knife, scrape the old adhesive smooth to a thickness of about 2 mm (0.8 in) on the bonding surface around the entire quarter glass opening flange:
    • Do not scrape down to the painted surface of the body; damaged paint will interfere with proper bonding.
    • If any of the clips are broken, remove them from the body.
    • Mask off surrounding surfaces before applying primer.
  7. 7.
    Clean the body bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the glass surface.
  8. 8.
    If the old quarter glass is to be reinstalled, use a putty knife to scrape off all traces of old adhesive from the quarter glass. Scrape the old adhesive from the molding with a knife, then clean the quarter glass and molding surfaces with alcohol where adhesive is to be applied. Make sure the bonding surface is kept free of water, oil and grease.
  1. 9.
    Set the quarter glass front trim, then install the upper clip and lower clip.
Illustration: QUARTER GLASS; UPPER CLIP; QUARTER GLASS FRONT TRIM; LOWER CLIP; No clearance area to the clip and trim.
  1. 1. QUARTER GLASS
  2. 2. UPPER CLIP
  3. 3. QUARTER GLASS FRONT TRIM
  4. 4. LOWER CLIP
  5. 5. No clearance area to the clip and trim.

PDF p. 967 · 20-31

  1. 10.
    Install the rear clip as shown.
Illustration: QUARTER GLASS; REAR CLIP
  1. 1. QUARTER GLASS
  2. 2. REAR CLIP
  1. 11.
    Set the quarter glass rear trim, then glue the upper rubber dam and lower rubber dam as shown.
Illustration: UPPER RUBBER DAM; QUARTER GLASS REAR TRIM; QUARTER GLASS FRONT TRIM; LOWER RUBBER DAM; QUARTER GLASS
  1. 1. UPPER RUBBER DAM
  2. 2. QUARTER GLASS REAR TRIM
  3. 3. QUARTER GLASS FRONT TRIM
  4. 4. LOWER RUBBER DAM
  5. 5. QUARTER GLASS
  1. 12.
    With a sponge, apply a light coat of glass primer to the inside face of the quarter glass as shown, then lightly wipe it of with gauze or cheesecloth.
    • Do not apply body primer to the quarter glass and do not get body and glass primer sponges mixed up.
    • Never touch the primed surfaces with your hands. If you do the adhesive may not bond to the quarter glass properly, causing a leak after the quarter glass is installed.
    • Keep water, dust and abrasive materials away from the primed surface.
Illustration: Apply glass primer here.; QUARTER GLASS; UPPER RUBBER DAM; Inside; QUARTER GLASS REAR TRIM; QUARTER GLASS FRONT TRIM; LOWER RUBBER DAM
  1. 1. Apply glass primer here.
  2. 2. QUARTER GLASS
  3. 3. UPPER RUBBER DAM
  4. 4. Inside
  5. 5. QUARTER GLASS REAR TRIM
  6. 6. QUARTER GLASS FRONT TRIM
  7. 7. LOWER RUBBER DAM

PDF p. 968 · 20-32

  1. 13.
    With a sponge, apply a light coat of body primer to the original adhesive remaining around the quarter glass opening flange. Let the body primer dry for at least 10 minutes.
    • Do not apply glass primer to the body and be careful not to mix up glass and body primer sponges.
    • Never touch the primed surfaces with your hands.
    • Mask off the dashboard before painting the flange.

Crosshatching on drawing denotes: Apply body primer here.

Illustration: Apply body primer here
  1. 1. Apply body primer here
  1. 14.
    Before filling a cartridge, cut a ”V” in the end of the nozzle as shown.
Illustration: NOZZLE
  1. 1. NOZZLE
  1. 15.
    Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a caulking gun and run a bead of adhesive around the edge of the quarter glass as shown:
    • After applying the adhesive, peel the separator off the butyl tape.
    • Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker bead at each corner.
Illustration: QUARTER GLASS; UPPER RUBBER DAM; Inside; QUARTER GLASS FRONT TRIM; QUARTER GLASS REAR TRIM; LOWER RUBBER DAM
  1. 1. QUARTER GLASS
  2. 2. UPPER RUBBER DAM
  3. 3. Inside
  4. 4. QUARTER GLASS FRONT TRIM
  5. 5. QUARTER GLASS REAR TRIM
  6. 6. LOWER RUBBER DAM

PDF p. 969 · 20-33

  1. 16.
    Use suction cups to hold the quarter glass over the opening and set it down on the adhesive. Lightly push on the quarter glass until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until the adhesive is dry.
  2. 17.
    Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the quarter glass, wipe with a soft shop towel dampened with alcohol.
  3. 18.
    Let the adhesive dry for at least one hour, then spray water over the quarter glass and check for leaks. Mark leaking areas and let the quarter glass dry, then seal with sealant. Let the vehicle stand for at least four hours after quarter glass installation. If the vehicle has to be used within the first four hours, it must be driven slowly.
  4. 19.
    Reinstall all remaining removed parts. Advise the customer not to do the following things for two to three days:
    • Slam the doors with all the windows rolled up.
    • Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads).