Workshop manual

Body Paint Repair - Soft Chipping Guard

Primer Coat Coating Procedures

Body Repair Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1693, 1694 (manual pages 8-13 to 8-14)

PDF p. 1693 · 8-13

NOTE: This section covers the application of the soft chipping primer to the replacement part.

  1. 1.
    Sanding the replacement part

Sand the area to be painted with #240-#400 sandpaper.

NOTE:

  • Do not oversand the edges or corners of the part.
  • Do not expose bare metal.
  1. 2.
    Air blowing/degreasing

Clean the surface with compressed air and wax and grease remover.

  1. 3.
    Masking
    • Place masking tape or paper around the surface to be painted.
    • Cover as wide an area as possible with tape or paper to keep primer from spreading.
  2. 4.
    Spraying chipping guard primer.
    • Stir the primer thoroughly.
    • Put the primer in a beaker and weigh the needed amount of primer to be used.
    • Mix the hardener into the primer, following the manufacturer's instructions.

NOTE: Measure the primer and hardener so they are in correct ratio.

ItemPrimer Hardener
* High Primer Surfacer 2C10:1
* Auto Primer Surfacer5:1

Mighty

  • Add the specified thinner to the mixture of hardener and primer to attain the proper viscosity for spraying

    2C 68°F (20°C) 18 sec + 1

  • These substances are not available with Dupont's 123 Vinyl Coating or Sherwin-William's Vinyl Gravel Guard. Follow the manufacturer's instructions for application.
  • Use the following materials:
    • Spies Hecker Permacron 4:1 Surfacer 4:1 (Hoechst)
    • Standox 2K 4:1 Special Filter (Herberts).
  • Once mixed with the hardener and thinner, the primer must be used within the times shown below.
Temperature41°F50°F68°F
(5°C)(10°C) (20°C)
High Primer
Surfacer 2C30H24H8H

Time

Auto Primer

Surfacer Mighty 4H 3.5H 3H

PDF p. 1694 · 8-14

  • Fill the gun's paint cup with the primer. Use a strainer when pouring the primer into the cup.
  • Primer should never be applied to a dirty or greasy surface. Before spraying, blow dust and dirt off the surface and clean with wax and grease remover. (Method of spraying)
  • Do not try to cover the surface with one heavy coat. Apply several thin coats.

NOTE:

  • Spray coat 4 - 5 coats to get 20 microns of thickness, as one coat deposits 5 - 7 microns.
  • Spray the primer at 250 - 300 kPa (2.5 - 3.0 kgf/cm2, 35.6 - 42.7 psi) pressure. Spraying with improper air pressure will cause imperfections.
  • Open the gun 3 - 4 turns.
  • Wipe up unwanted primer immediately with thinner.
  1. 5.
    Cleaning spray gun
    • After spraying, be sure to clean the spray gun thoroughly with thinner or solvent.
    • The gun will be permanently clogged if the primer is allowed to dry.
  2. 6.
    Drying
    • After spraying the chipping guard primer, air-dry for 7 - 1- minutes to evaporate the thinner in the primer. Then dry it with infrared lamps at 176°F (80°C) for 30 - 40 minutes.

NOTE: Insufficient baking may cause pinholes if the

primer coat is too thick.

  • The temperature lamps and drying time recommendations should be followed closely.
  1. 7.
    Intermediate and Top coating.
    • Sand the chipping guard primer film with #280 - #400 sandpaper.
    • Follow the intermediate/top coating Procedures (see page 8-8).
Temperature41°F (5°C)68°F (20°C)86°F (30°C)140°F (60°C)176°F (80°C)
TimeBefore8 - 13H3.5 - 5H2 - 3H30 Min.20 Min.
sanding6 - 10H4 - 5H2 - 4H15 - 20 Min.10 - 15 Min.
MinimumBefore8H4H3H30 Min20 Min.
timePainting10 - 18H6 - 8H4 - 8H20 - 40 Min.15 - 30 Min.

NOTE: The upper line of time shows specifications for High Primer Surfacer 2C, and the lower line Auto Primer Surfacer Mighty.