Workshop manual

Symptom-to-Component Chart

Electrical System

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 593, 594 (manual pages 14-38 to 14-39)

PDF p. 593 · 14-38

DiagnosticD IndicatorSymptomPossible CauseRefer to
Trouble Code*LightPage
5Blinks♦ Transmission shifts♦Short in A/T gear position switch(See page
same as D positionwire14-40)
in any of the positions.♦Faulty A/T gear position switch
6OFF♦ Transmission shifts♦Disconnected A/T gear position(See page
same as D positionswitch connector14-42)
in any positions.♦Open in A/T gear position switch
wire
♦Faulty A/T gear position switch
30Blinks♦ Poor acceleration,♦Disconnected solenoid harness(See page
flares on starting off.connector14-44)
♦Short or open in shift control linear
solenoid wire
♦Faulty shift control linear solenoid
♦Open in VB SOL line
♦Faulty PG line
31Blinks♦ Poor acceleration,♦Disconnected solenoid harness(See page
flares on starting off.connector14-46)
♦Short or open in PH-PL control
linear solenoid wire
♦Faulty PH-PL control linear solenoid
♦Open in VB SOL line
♦Faulty PG line
32Blinks♦ Poor acceleration,♦Disconnected solenoid harness(See page
flares on starting off.connector14-48)
♦Short or open in start clutch control
linear solenoid wire
♦Faulty start clutch control linear
solenoid
♦Open in VB SOL line
♦Faulty PG line
33Blinks♦ No specific symptom♦Disconnected solenoid harness(See page
appears.connector14-50)
♦Short or open in inhibitor solenoid
wire
♦Faulty inhibitor solenoid
♦Open in VB SOL line
♦Faulty PG line
34Blinks♦ Poor acceleration,♦Disconnected drive pulley speed(See page
flares on starting off.sensor connector14-52)
♦Short or open in drive pulley speed
sensor wire
♦Faulty drive pulley speed sensor
35Blinks♦ Poor acceleration,♦Disconnected driven pulley speed(See page
flares on starting off.sensor connector14-54)
♦Short or open in driven pulley speed
sensor wire
♦Faulty driven pulley speed sensor
36Blinks♦ Poor acceleration,♦Disconnected secondary gear shaft(See page
flares on starting off.speed sensor connector14-56)
♦Short or open in secondary gear
shaft speed sensor wire
♦Faulty secondary gear shaft speed
sensor
42Blinks♦ Poor acceleration,♦Faulty shift control system(See page
flares on starting off.14-58)
43Blinks♦ Poor acceleration,♦Faulty start clutch control system(See page
flares on starting off.14-59)

Diagnostic Trouble Code*: The DTCs are the number of the D indicator light blinks when the service check connector is connected with the special tool (SCS Short Connector)

PDF p. 594 · 14-39

If the self-diagnostic D indicator light does not blink, perform an inspection according to the table below.

SymptomInspectionRef. Page
D indicator light is on constantly (not blinking) whenever the-(see page
ignition switch is ON (II)14-61)
D indicator light does not come on for two seconds after ignition-(see page
switch is first turned ON (II)14-62)
Transmission does not shift up into S mode with turning the modeInspect mode switch.(see page
switch on.14-64)
S indicator light does not come on when S mode selected in DInspect S mode indicator light(see page
positioncircuit14-66)
Shift lever cannot be moved from P position with the brake pedalCheck shift lock system(see page
depressed. (KQ, KU model only)14-67)
Ignition key cannot be moved from ACC (I) position to LOCK (0)Check key interlock system(see page
position with the shift lever in P position. (KQ, KU model only)14-68)

NOTE:

  • If a customer described the symptom for code 6, it will be necessary to recreate the symptom by test driving, then recheck the DTC.
  • Sometime the indicator light and the Malfunction Indicator Lamp (MIL) may come on simultaneously. If so, repair the PGM-FI system according to the DTC, then reset the memory by removing the BACK-UP fuse in the under-dash fuse/relay box for more than 10 seconds. Drive the car for several minutes at a speed over 30 mph (50 km/h), then recheck the DTC.