Workshop manual

Differential

Tapered Roller Bearing Preload Adjustment

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 519, 520 (manual pages 13-45 to 13-46)

PDF p. 519 · 13-45

NOTE: If any of the items listed below are replaced, the tapered roller bearing preload must be adjusted.

  • Transmission housing
  • Clutch housing
  • Differential carrier
  • Tapered roller bearing and bearing outer race
  • Thrust shim
  • 75 mm shim
  1. 1.

    Remove the bearing outer race and thrust shim from the transmission housing (See page 13-44).

    NOTE: Install the thrust shim only on the transmission housing side.

NOTE: Before adjusting the tapered roller bearing preload, let the transmission cool to room temperature if the bearing outer race was removed by heating the clutch housing.

  1. 2.
    First try the same size thrust shim that was removed.
Illustration: THRUST SHIM; TRANSMISSION HOUSING
  1. 1. THRUST SHIM
  2. 2. TRANSMISSION HOUSING
  1. 3.

    After installing the thrust shim, install the bearing outer race in the transmission housing (See page 13-40).

    NOTE:

    • Install the bearing outer race squarely.
    • Check that there is no clearance between the bearing outer race, thrust shim and transmission housing.
  2. 4.

    With the mainshaft and countershaft removed, install the differential assembly, and torque the clutch housing and transmission housing.

    NOTE: It is not necessary to use sealing agent between the housings.

    TORQUE: 8x 1.25 mm, 27 Nm (2.8 kgf/m, 20 lbf/ft)

  3. 5.
    Rotate the differential assembly in both directions to seat the tapered roller bearings.
  4. 6.

    Measure the starting torque of the differential assembly with the special tool and a torque wrench.

    STANDARD: 1.4 - 2.5 Nm (14 - 26 kgf/m, 12 - 23 lbf/ft)

    NOTE:

    • Measure the tapered roller bearing preload at normal room temperature.
    • Measure the tapered roller bearing preload in both directions.
Illustration: TORQUE WRENCH; PRELOAD INSPECTION TOOL, 07HAJ-PK40201
  1. 1. TORQUE WRENCH
  2. 2. PRELOAD INSPECTION TOOL, 07HAJ-PK40201

PDF p. 520 · 13-46

  1. 7.

    If the tapered roller bearing preload is not within the standard, select the thrust shim which will give the correct tapered roller bearing preload from the following table.

    NOTE: Changing the thrust shim to the next size will increase or decrease tapered roller bearing preload by approx 0.3 - 0.4 Nm (3 -4 kgf/m, 2.6 - 3.5 lbf/in). THRUST SHIM

Part NumberThickness
A41381-PX5-B001.90 mm (0.0748 in)
B41382-PX5-B001.93 mm (0.0760 in)
C41383-PX5-B001.96 mm (0.0772 in)
D41384-PX5-B001.99 mm (0.0783 in)
E41385-PX5-B002.02 mm (0.0795 in)
F41386-PX5-B002.05 mm (0.0807 in)
G41387-PX5-B002.08 mm (0.0819 in)
H41388-PX5-B002.11 mm (0.0831 in)
I41389-PX5-B002.14 mm (0.0843 in)
J41390-PX5-B002.17 mm (0.0854 in)
K41391-PX5-B002.20 mm (0.0866 in)
L41392-PX5-B002.23 mm (0.0878 in)
M41393-PX5-B002.26 mm (0.0890in)
N41394-PX5-B002.29 mm (0.0902 in)
O41395-PX5-B002.32 mm (0.0913 in)
P41396-PX5-B002.35 mm (0.0925in)
Q41397-PX5-B002.38 mm (0.0937 in)
R41398-PX5-B002.41mm (0.0949 in)
S41399-PX5-B002.44mm (0.0961 in)
T41400-PX5-B002.47mm 10.0972 in)
AA41873-PX5-B001.66 mm (0.0654 in)
AB41874-PX5-B001.69 mm (0.0665 in)
AC41875-PX5-B001.72 mm (0.0677 in)
AD41876-PX5-B001.75 mm (0.0689 in)
AE41877-PX5-B001.78 mm (0.0701 in)
AF41878-PX5-B001.81 mm (0.0713 in)
AG41879-PX5-B001.84 mm (0.0724 in)
AH41880-PX5-B001.87 mm (0.0736 in)
  1. 8.
    Recheck the tapered roller bearing preload.
  2. 9.

    How to select the correct thrust shim:

    -1) Compare the tapered roller bearing preload you get with the thrust shim that was removed, with the specified preload of 1.4 - 2.5 Nm (14 - 26 kgf/cm, 12 - 23 lbf/in).

    -2) If your measured tapered roller bearing preload is less than specified, subtract yours from the specified.

    If yours is more than the specified, subtract the specified from your measurement.

    For example with a 2.17 mm (0.0854 in) thrust shim:

    (A) specified 2.5 Nm (26 kgf/cm, 23 lbf/in)

    • you measure 0.6 Nm (6 kgf/cm, 5 lbf/in)

      1.9 Nm (20 kgf/cm, 18 lbf/in) less

(B)

you measure 3.3 Nm (34 kgf/cm, 30 lbf/in)

- specified 2.5 Nm (26 kgf/cm, 23 lbf/in)

0.8 Nm (8 kgf/cm, 7 lbf/in)

-3) Each shim size up or down from standard

makes about 0.3 - 0.4 Nm (3 -4 kgf/cm, 2.6 - 3.5 lbf/in) difference in tapered roller bearing preload.

In an example (A), your measured tapered roller bearing preload was 1.9 Nm (20 kgf/cm, 18 lbf/in) less than standard so you need a thrust shim five sizes thicker than standard (try the 2.32 mm (0.0913 in) thrust shim and recheck).

In example (B), your measurement was 0.8 Nm (8 kgf/cm, 7lbf/in) more than standard, so you need a thrust shim two sizes thinner (try the 2.1 mm (0.0831 in) thrust shim and recheck).