Workshop manual

Oil Pan

Installation

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 295, 296 (manual pages 7-25 to 7-26)

PDF p. 295 · 7-25

Europe, Australia and South Africa models:

NOTE:

  • Use liquid gasket, part No. 08C70-K0234M, 08C70-K0334M or 08C70-X0331S.
  • Check that the mating surfaces are clean and dry before applying liquid gasket.
  • Apply liquid gasket evenly, being careful to cover all the mating surface.
  • To prevent leakage of oil, apply liquid gasket to the inner threads of the bolt holes.
  • Do not install the parts if five minutes or more have elapsed since applying the liquid gasket. Instead, reapply liquid gasket after removing the old residue.
  • After assembly, wait at least 30 minutes before filling the engine with oil.
  1. 1.
    Install the oil pan gasket on the oil pan.
Illustration: OIL PAN; OIL PAN GASKET. Replace.
  1. 1. OIL PAN
  2. 2. OIL PAN GASKET. Replace.
  1. 2.
    Apply liquid gasket to the block mating surfaces of the oil pan, then install it.
    • Apply liquid gasket to the shaded areas.
Illustration: OIL PAN
  1. 1. OIL PAN
  1. 3.
    Tighten nuts finger-tight at six points as shown below.
Illustration · Europe, Australia and South Africa models
  1. 4.

    Tighten all bolts and nuts, starting from nut (1), clockwise in three steps.

    NOTE: Excessive tightening can cause distortion of the oil pan gasket and oil leakage.

    Torque: 12 Nm (1.2 kgf/m, 8.7 lbf/ft)

PDF p. 296 · 7-26

Except Europe, Australia and South Africa models:

NOTE:

  • Use liquid gasket, part No. 08C70-K0234M, 08C70-K0334M or 08C70-X0331S.
  • Check that the mating surfaces are clean and dry before applying liquid gasket.
  • Apply liquid gasket evenly, being careful to cover all the mating surface.
  • To prevent leakage of oil, apply liquid gasket to the inner threads of the bolt holes.
  • Do not install the parts if five minutes or more have elapsed since applying the liquid gasket. Instead, reapply liquid gasket after removing the old residue.
  • After assembly, wait at least 30 minutes before filling the engine with oil.
  1. 1.
    Apply liquid gasket on the oil pump and right side cover mating areas as shown below:
Illustration: CYLINDER BLOCK; Apply liquid gasket to these points.; OIL PUMP; Apply liquid gasket to these points.; RIGHT SIDE COVER
  1. 1. CYLINDER BLOCK
  2. 2. Apply liquid gasket to these points.
  3. 3. OIL PUMP
  4. 4. Apply liquid gasket to these points.
  5. 5. RIGHT SIDE COVER
  1. 2.

    Install the oil pan gasket and oil pan.

    NOTE:

    • Use a new oil pan gasket.
    • Install oil pan no more than five minutes after liquid gasket has been applied.
Illustration: OIL PAN; Apply liquid gasket to these points.; OIL PAN GASKET. Replace.; Apply liquid gasket to these points
  1. 1. OIL PAN
  2. 2. Apply liquid gasket to these points.
  3. 3. OIL PAN GASKET. Replace.
  4. 4. Apply liquid gasket to these points
  1. 3.
    Tighten nuts finger-tight at six points as shown below.
Illustration · Except Europe, Australia and South Africa models
  1. 4.

    Tighten all bolts and nuts, starting from nut (1), clockwise in three steps.

    NOTE: Excessive tightening can cause distortion of the oil pan gasket and oil leakage.

    Torque: 12 Nm (1.2 kgf/m, 8.7 lbf/ft)