Workshop manual

Cylinder Head

Installation

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 269, 270 (manual pages 6-30 to 6-31)

PDF p. 269 · 6-30

  1. 2.
    Position the camshaft correctly (see page 6-10).
  2. 3.

    Tighten the cylinder head bolts sequentially in four steps.

    1st step: (1) - (10) 20 Nm (2.0 kgf/m, 14 Ibf/ft)

    2nd step: (1) - (10) 49 Nm (5.0 kgf/m, 36 Ibf/ft)

    3rd step: (1) - (10) 67 Nm (6.8 kgf/m, 49 Ibf/ft)

    4th step: (1),(2) 67 Nm (6.8 kgf/m, 49 Ibf/ft)

    NOTE:

    • We recommend using a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten.
    • If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the 1st step.

CYLINDER HEAD BOLT TORQUE SEQUENCE:

Illustration · CYLINDER HEAD BOLT TORQUE SEQUENCE
  1. 4.
    Install the intake manifold and tighten the nuts in a criss-cross pattern in two or three steps, beginning with the inner nuts (see page 9-2).
  2. 5.
    Install the exhaust manifold and tighten the nuts in a criss-cross pattern in two or three steps, beginning with the inner nut (see page 9-3).
  3. 6.
    Install the exhaust manifold bracket, then install the exhaust pipe A and the bracket, and then install the cover.
  1. 7.
    Install the timing belt (see page 6-10).
  2. 8.
    Adjust the valve clearance (see page 6-3).
  3. 9.

    Install the head cover gasket in the groove of the cylinder head cover. Seat the recesses for the camshaft first, then work it into the groove around the outside edges.

    NOTE:

    • Before installing the head cover gasket, thoroughly clean the seal and the groove.
    • When installing, make sure the head cover gasket is seated securely in the corners of the recesses with no gap.
Illustration: HEAD COVER GASKET. Clean; CORNERS OF THE RECESS; CYLINDER HEAD COVER; CORNERS OF THE RECESS
  1. 1. HEAD COVER GASKET. Clean
  2. 2. CORNERS OF THE RECESS
  3. 3. CYLINDER HEAD COVER
  4. 4. CORNERS OF THE RECESS
  1. 10.

    Apply liquid gasket to the head cover gasket at the four corners of the recesses.

    NOTE:

    • Use liquid gasket, Part No. 08C70 - K0234M, 08C70 - K0334M or 08C70 - X0331S.
    • Check that the mating surfaces are clean and dry before applying liquid gasket.
    • Do not install the parts if five minutes or more have elapsed since applying liquid gasket. Instead, reapply liquid gasket after removing old residue.
    • After assembly, wait at least 30 minutes before filling the engine with oil.
Illustration: Apply liquid gasket to the shaded areas.
  1. 1. Apply liquid gasket to the shaded areas.

PDF p. 270 · 6-31

  1. 11.

    When installing the cylinder head cover, hold the head cover gasket in the groove by placing your fingers on the camshaft holder contacting surfaces (top of the semicircles).

    Set the spark plug seal on the spark plug pipe. Once the cylinder head cover is on the cylinder head, slide the cover slightly back and forth to seat the head cover gasket.

    NOTE:

    • Before installing the cylinder head cover, clean the cylinder head contacting surfaces with a shop towel.
    • Do not touch the parts where liquid gasket was applied.
    • Take care not to damage the spark plug seal when installing the cylinder head cover.
    • Visually check the spark plug seal for damage.
    • Replace the washer when damaged or deteriorated.
Illustration: WASHER; CYLINDER HEAD COVER; SPARK PLUG SEAL
  1. 1. WASHER
  2. 2. CYLINDER HEAD COVER
  3. 3. SPARK PLUG SEAL
  1. 12.

    Tighten the nuts in two or three steps. In the final step, tighten all bolts, in sequence, to 9.8 Nm (1.0 kgf/m, 7.2 lbf/ft).

    NOTE: After assembly, wait at least 30 minutes before filling the engine with oil.

Illustration · Cylinder Head · Installation
  1. 13.
    After installation, check that all tubes, hoses and connectors are installed correctly.