Workshop manual

Wire Harness and Connectors

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1278, 1279 (manual pages 24-15 to 24-16)

PDF p. 1278 · 24-15

Connector No. *1Wire harness and connectorTerminalNote *2Ref. No.
MaleFemale
FoSRS main harness 2P connectorO(1)1
U1oSRS main harness 14P connectorO(1)3
U2oSRS floor harness 18P connectorO(1)4
D1D1oDriver’s airbag 2P connectorO(1)(2)1
D1D1iCable reel 2P connectorO(1)(2)2
D2D2oCable reel 2P connectorO(1)1
D2D2iSRS main harness 2P connectorO(1)2
P1P1oFront passenger’s airbag connectorO(1)(2)1
P1P1iSRS main harness 2P connectorO(1)(2)2
TL1TL1oLeft side seat belt tensioner 2P connectorO(1)2)1
TL1TL1iSRS floor harness 2P connectorO(1)(2)2
TR1TR1oRight side seat belt tensioner 2P connectorO((1)2)1
TR1TR1iSRS main harness 2P connectorO(1)(2)2
C1Gauge assembly sub-harness 16P connectorO5
C2Gauge assembly sub-harness 24P connectorO6
C3Main wire harness 24P connectorO7
C4Gauge assembly sub-harness 16P connectorO8
C5Main wire harness 16P connectorO9
C6SRS main harness 2P connectorO10
  • *1
    : The connector numbers is original in this section that are different from other sections.
  • *2
    : Note
    1. (1)
      : Spring loaded lock connector
    2. (2)
      : With built-in short contact connector
Illustration · Wire Harness and Connectors

PDF p. 1279 · 24-16

The SRS is a safety device which, when used in conjunction with the seat belt, is designed to help protect the driver and front passenger in a frontal impact exceeding a certain set limit. The system consists of the SRS unit (including safety sensor and impact sensor), the cable reel, the driver’s airbag and front passenger’s airbag.

Seat Belt Tensioner

The seat belt tensioner is linked with the SRS airbags to further increase the effectiveness of the seat belt. In a front-end collision, the tensioner instantly retracts the belt firmly to secure the occupants in their seats.

Illustration: CABLE REEL; DRIVER’S AIRBAG; FRONT PASSENGER’S AIRBAG; RIGHT SIDE SEAT BELT TENSIONER; SRS UNIT; LEFT SIDE SEAT BELT TENSIONER
  1. 1. CABLE REEL
  2. 2. DRIVER’S AIRBAG
  3. 3. FRONT PASSENGER’S AIRBAG
  4. 4. RIGHT SIDE SEAT BELT TENSIONER
  5. 5. SRS UNIT
  6. 6. LEFT SIDE SEAT BELT TENSIONER

Operation

The main circuit in the SRS unit senses and judges the force of impact and, if necessary, ignites the inflator charges. If battery voltage is too low or power is disconnected due to the impact, the voltage regulator and the back-up power circuit respectively will keep voltage at a constant level.

For the SRS to operate:

  1. (1)
    The impact sensor must activate and send electric signals to the microprocessor.
  2. (2)
    The microprocessor must compute the signals and send them to the airbag inflators and seat belt tensioners.
  3. (3)
    The inflators must ignite and deploy the airbags and activate the tensioners.
Illustration · For the SRS to operate

Self-diagnosis System

A self-diagnosis circuit is built into the SRS unit; when the ignition switch is turned ON (II), the SRS indicator light comes on and goes off after about six seconds if the system is operating normally.

If the light does not come on, or does not go off after six seconds or if it comes on while driving, it indicates an abnormality in the system. The system must be inspected and repaired as soon as possible.

For better serviceability, the SRS unit memory stores the cause of the malfunction and the unit is connected to the data link connector (DLC). This information can be read with the Honda PGM Tester when it is connected to the DLC (3P).