Workshop manual

Integrated Control Unit

Input Test

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1198, 1199 (manual pages 23-E-4 to 23-E-5)

PDF p. 1198 · 23-E-4

  1. 1.
    Remove the driver’s lower pocket (see section 20).
  2. 2.
    Disconnect the 12P connector from the integrated control unit.
  3. 3.
    Inspect the connector and socket terminals to make sure they are all making good contact.
    • If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
    • If the terminals look OK, make the following input tests at the connector.
      • If any test indicates a problem, find and correct the cause, then recheck the system.
      • If all the input tests prove OK, the control unit must be faulty, replace it.
Illustration: INTEGRATED CONTROL UNIT; 12P CONNECTOR; Wire side of female terminals; BLU/RED; RED/BLK; GRN/RED [LT GRN/RED]; GRN; BLU/WHT; BLK; GRN/WHT; YEL/BLU; WHT/BLU; BLU/BLK
  1. 1. INTEGRATED CONTROL UNIT
  2. 2. 12P CONNECTOR
  3. 3. Wire side of female terminals
  4. 4. BLU/RED
  5. 5. RED/BLK
  6. 6. GRN/RED [LT GRN/RED]
  7. 7. GRN
  8. 8. BLU/WHT
  9. 9. BLK
  10. 10. GRN/WHT
  11. 11. YEL/BLU
  12. 12. WHT/BLU
  13. 13. BLU/BLK

[ ]: Without keyless entry system

PDF p. 1199 · 23-E-5

Intermittent Wiper Relay System

CavityWireTest conditionTest: Desired resultPossible cause if result is
not obtained
1BLKUnder all conditionsCheck for continuity to ground:♦Poor ground (G401, G402)
There should be continuity♦An open in the wire
8YEL/BLUIgnition switch ON (II)Check for voltage to ground:♦Blown No 3 (20A) fuse in
and windshield wiperThere should be battery voltagetheunder-dash fuse/relay box.
switch at INT♦Faulty windshield wiper
switch
♦An open in the wire
2BLU/BLKIgnition switch ON (II)Check for voltage to ground:♦Blown No 3 (7.5A) fuse in
and windshield wiperThere should be battery voltagethe under-dash fuse/relay box.
switch at OFF or INT♦Faulty windshield wiper
switch
♦An open in the wire
♦Faulty windsheild wiper
motor
3BLU/WHTIgnition switch ON (II)Check for voltage to ground:♦Blown No 3 (20A) fuse in
There should be battery voltagetheunder-dash fuse/relay box.
♦Faulty windsheild wiper
motor
  • An open in the wire

Lights-on Reminder System

CavityWireTest conditionTest: Desired resultPossible cause if result is
not obtained
1BLKUnder all conditionsCheck for continuity to ground:♦Poor ground (G401, G402)
There should be continuity♦An open in the wire
10RED/BLKCombination lightCheck for voltage to ground:♦Blown No 46 (7.5A) fuse in
switch ONThere should be battery voltagethe under-hood fuse/relay box.
♦Faulty combination light
switch
♦An open in the wire
♦Faulty taillight relay
11GRN/WHTIgnition switch ON (II)Check for voltage to ground:♦Blown No 5 (10A) fuse in
There should be battery voltagetheunder-dash fuse/relay box.
♦An open in the wire
6GRNDriver’s door openCheck for continuity to ground:♦Faulty driver’s door switch
There should be continuity♦Poor ground
♦An open in the wire
7GRN/REDPassenger’s door openCheck for continuity to ground:♦Faulty passenger’s door
[LTThere should be continuityswitch
GRN/RED]♦Poor ground
♦An open in the wire

[ ]: Without keyless entry system

Key-in Reminder System

CavityWireTest conditionTest: Desired resultPossible cause if result is
not obtained
5WHT/BLUUnder all conditionsCheck for voltage to ground:♦Blown No 23 (7.5A) fuse in
There should be battery voltagethe under-dash fuse/relay box.
♦An open in the wire
11GRN/WHTUnder all conditionsCheck for voltage to ground:♦Blown No. 5 (7.5A) fuse in
There should be battery voltagethe under-dash fuse/relay box
♦An open in the wire
6GRNCheck for voltage to ground:♦Faulty driver’s door switch
There should be 1V or less♦An open in the wire
12BLU/REDUnder all conditionsCheck for voltage to ground:♦Faulty ignition key switch
There should be 1V or less♦Poor ground G401, G402)
♦An open in the wire