Workshop manual

Glass

Quarter Glass Replacement

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF pages 1972, 1973, 1974, 1975, 1976 (manual pages 20-23 to 20-27)

PDF p. 1972 · 20-23

5D:

NOTE:

  • Put on gloves to protect your hands.
  • When removing the glass with the piano wire, put on eye protection to protect your eyes.
  • Use seat covers and plastic plate to avoid damaging any surfaces.
  • Use glass adhesive set P/N. 08C73 - X0230N.
  1. 1.
    Remove:
    • Rear side shelf (See Page 20-29)
    • Trunk side trim panel (See Page 20-29)
    • Quarter pillar trim (See Page 20-30)
    • Rear pillar trim (See Page 20-30)
    • Taillight
  2. 2.
    Pull down the rear side portion of the headliner. Take care not to bend the headliner excessively, or you may crease or break it.
  3. 3.

    Remove the quarter glass front seal and quarter glass rear trim.

    NOTE: Replace the quarter glass front seal and quarter glass rear trim.

  4. 4.
    Apply protective tape along the edge of the body and the related parts.
  5. 5.
    Using an awl, make a hole through the adhesive from inside the vehicle at the corner portion of the quarter glass.
  6. 6.
    Push a piece of piano wire through the hole, and wrap each end around a piece of wood.
  7. 7.
    Carefully cut through the adhesive around the entire quarter glass as follows:
    • Straight portion: Hold a piece of wood inside the vehicle, and with a helper on the outside, pull back the piano wire.
    • Corner portion: Pull back each end of the piano wire.

Cutting positions with the piano wire:

Illustration: TRIM UPPER CLIP; UPPER CLIP; PIANO WIRE; UPPER CLIP; PIANO WIRE; LOWER CLIP; ADHESIVE; PIANO WIRE; TRIM LOWER CLIP; PIANO WIRE
  1. 1. TRIM UPPER CLIP
  2. 2. UPPER CLIP
  3. 3. PIANO WIRE
  4. 4. UPPER CLIP
  5. 5. PIANO WIRE
  6. 6. LOWER CLIP
  7. 7. ADHESIVE
  8. 8. PIANO WIRE
  9. 9. TRIM LOWER CLIP
  10. 10. PIANO WIRE
  1. 8.
    Carefully remove the quarter glass.
  2. 9.
    With a knife, scrape the old adhesive smooth to a thickness of about 2 mm (0.08 in.) on the bonding surface around the entire quarter glass opening flange:
    • Do not scrape down to the painted surface of the body; damaged paint will interfere with proper bonding.
    • Remove the remaining parts from the body.
    • Mask off surrounding surfaces before painting.
  3. 10.
    Clean the body bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the clean surface.
  4. 11.
    If the old quarter glass is to be reinstalled, use a putty knife to scrape off all of the old adhesive from the quarter glass. Clean the quarter glass with alcohol where new adhesive is to applied. Make sure the bonding surface is kept free of water, oil and grease.

PDF p. 1973 · 20-24

  1. 12.
    Glue the upper and lower clips to the inside face of the quarter glass, and glue the quarter glass front seal:
    • Apply a light coat of primer (3M C-100, or equivalent), and glue the upper clips with urethane adhesive and adhesive tape, lower clip with adhesive tape, and seal with urethane adhesive.
    • Never touch the primed surfaces with your hands.
    • Be careful not to touch the quarter glass where adhesive will be applied.
    • Keep water, dust, and abrasive materials away from the primed surface.
Illustration: UPPER CLIP; Turn the alignment mark to the bottom.; ADHESIVE TAPE; GLASS; Inside; UPPER CLIP; ADHESIVE TAPE; ADHESIVE; Adhesive areas.; UPPER CLIP; GLASS; Adhesive area.; LOWER CLIP; Turn the alignment mark to the bottom; QUARTER GLASS FRONT SEAL; Inside; Adhesive area.
  1. 1. UPPER CLIP
  2. 2. Turn the alignment mark to the bottom.
  3. 3. ADHESIVE TAPE
  4. 4. GLASS
  5. 5. Inside
  6. 6. UPPER CLIP
  7. 7. ADHESIVE TAPE
  8. 8. ADHESIVE
  9. 9. Adhesive areas.
  10. 10. UPPER CLIP
  11. 11. GLASS
  12. 12. Adhesive area.
  13. 13. LOWER CLIP
  14. 14. Turn the alignment mark to the bottom
  15. 15. QUARTER GLASS FRONT SEAL
  16. 16. Inside
  17. 17. Adhesive area.
  1. 13.
    Glue the rubber dam to the inside face of the quarter glass. Be careful not to touch the quarter glass where adhesive will be applied.
Illustration: UPPER RUBBER DAM; QUARTER GLASS FRONT SEAL; UPPER RUBBER DAM; GLASS; LOWER RUBBER DAM; QUARTER GLASS FRONT SEAL; LOWER RUBBER DAM
  1. 1. UPPER RUBBER DAM
  2. 2. QUARTER GLASS FRONT SEAL
  3. 3. UPPER RUBBER DAM
  4. 4. GLASS
  5. 5. LOWER RUBBER DAM
  6. 6. QUARTER GLASS FRONT SEAL
  7. 7. LOWER RUBBER DAM

PDF p. 1974 · 20-25

  1. 14.
    Install the trim upper clip and trim lower clip to the quarter glass rear trim, and install the quarter glass rear trim to the quarter glass. Be careful not to touch the quarter glass where adhesive will be applied.
Illustration: TRIM UPPER CLIP; QUARTER GLASS REAR TRIM; TRIM REAR CLIP; GLASS
  1. 1. TRIM UPPER CLIP
  2. 2. QUARTER GLASS REAR TRIM
  3. 3. TRIM REAR CLIP
  4. 4. GLASS
  1. 15.
    With a sponge, apply a light coat of glass primer to the inside face of the quarter glass as shown, then lightly wipe it off with gauze or cheesecloth:
    • Do not apply body primer to the quarter glass, and do not get body and glass primer sponges mixed up.
    • Never touch the primed surfaces with your hands. If you do the adhesive may not bond to the quarter glass properly, causing a leak after the quarter glass is installed.
    • Keep water, dust, and abrasive materials away from the primed surface.
Illustration: Apply glass primer here.; UPPER RUBBER DAM; GLASS; Inside; QUARTER GLASS REAR TRIM; LOWER RUBBER DAM; QUARTER GLASS REAR TRIM; GLASS; Inside; GLASS; LOWER RUBBER DAM; Inside; QUARTER GLASS FRONT SEAL
  1. 1. Apply glass primer here.
  2. 2. UPPER RUBBER DAM
  3. 3. GLASS
  4. 4. Inside
  5. 5. QUARTER GLASS REAR TRIM
  6. 6. LOWER RUBBER DAM
  7. 7. QUARTER GLASS REAR TRIM
  8. 8. GLASS
  9. 9. Inside
  10. 10. GLASS
  11. 11. LOWER RUBBER DAM
  12. 12. Inside
  13. 13. QUARTER GLASS FRONT SEAL
  1. 14.
    ALIGNMENT MARKS
  2. 15.
    ALIGNMENT MARKS
  3. 16.
    UPPER RUBBER DAM
  4. 17.
    GLASS
  5. 18.
    QUARTER GLASS FRONT SEAL
  6. 19.
    Inside

PDF p. 1975 · 20-26

  1. 16.
    With a sponge, apply a light coat of body primer to the original adhesive remaining around the quarter glass opening flange. Let the body primer dry for at least 10 minutes:
    • Do not apply glass primer to the body, and be careful not to mix up glass and body primer sponges.
    • Never touch the primed surfaces with your hands.
    • Mask off the interior parts before painting the flange.
Illustration: Apply body primer here.; Apply the adhesive along the bead.
  1. 1. Apply body primer here.
  2. 2. Apply the adhesive along the bead.
  1. 17.
    Thoroughly mix the adhesive and hardener together on a clean glass or metal plate with a putty knife. Follow the instructions that come with the adhesive.
  2. 18.
    Before filling a cartridge, cut a “V” in the end of the nozzle as shown.
Illustration: NOZZLE
  1. 1. NOZZLE
  1. 19.
    Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a chalking gun, and run a bead of adhesive around the edge of the glass as shown. Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker bead at each corner.
Illustration: ADHESIVE; UPPER RUBBER DAM; GLASS; Inside; QUARTER GLASS REAR TRIM; GLASS; QUARTER GLASS REAR TRIM; GLASS; Inside; GLASS; LOWER RUBBER DAM; Inside
  1. 1. ADHESIVE
  2. 2. UPPER RUBBER DAM
  3. 3. GLASS
  4. 4. Inside
  5. 5. QUARTER GLASS REAR TRIM
  6. 6. GLASS
  7. 7. QUARTER GLASS REAR TRIM
  8. 8. GLASS
  9. 9. Inside
  10. 10. GLASS
  11. 11. LOWER RUBBER DAM
  12. 12. Inside
  1. 13.
    LOWER RUBBER DAM
  2. 14.
    QUARTER GLASS FRONT SEAL
  3. 15.
    ALIGNMENT MARKS
  4. 16.
    ALIGNMENT MARKS
  5. 17.
    UPPER RUBBER DAM
  6. 18.
    GLASS
  7. 19.
    QUARTER GLASS FRONT SEAL
  8. 20.
    Inside

PDF p. 1976 · 20-27

  1. 20.
    Use suction cups to hold the glass over the opening, align the clips, and set it down on the adhesive. Lightly push on the glass until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until the adhesive is dry.
  2. 21.
    Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the glass, wipe with a soft shop towel dampened with alcohol.
  3. 22.
    Let the adhesive dry for at least one hour, then spray water over the glass and check for leaks. Mark leaking areas, and let the glass dry, then seal with sealant:
    • Let the vehicle stand for at least four hours after glass installation. If the vehicle has to be used within the first four hours, it must be driven slowly.
    • Keep the glass dry for the first hour after installation.
  4. 23.
    Reinstall all remaining removed parts. Advise the customer not to do the following things for two to three days:
    • Slam the doors with all the windows rolled up.
    • Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads).