Workshop manual

Doors

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF pages 1951, 1952, 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970 (manual pages 20-2 to 20-21)

PDF p. 1951 · 20-2

Component Location Index - 5D Front Door

Illustration: DOOR WEATHERSTRIP; CENTRE CHANNEL TAPE Replacement, (See Page 20-19); UPPER CHANNEL TAPE Replacement, (See Page 20-19); DOOR MOULDING; FRONT DOOR; HINGE; HINGE; DETENT ROD; PULL POCKET BRACKET; INNER WEATHERSTRIP; FRONT DOOR PANEL Removal and installation, (See Page 20-6); SPEAKER COVER; POWER WINDOW SWITCH; POWER WINDOW SWITCH; PULL POCKET PANEL; Passenger’s:; PULL POCKET PANEL; PLASTIC COVER; SPEAKER; ADAPTER
  1. 1. DOOR WEATHERSTRIP
  2. 2. CENTRE CHANNEL TAPE Replacement, (See Page 20-19)
  3. 3. UPPER CHANNEL TAPE Replacement, (See Page 20-19)
  4. 4. DOOR MOULDING
  5. 5. FRONT DOOR
  6. 6. HINGE
  7. 7. HINGE
  8. 8. DETENT ROD
  9. 9. PULL POCKET BRACKET
  10. 10. INNER WEATHERSTRIP
  11. 11. FRONT DOOR PANEL
    Removal and installation, (See Page 20-6)
  12. 12. SPEAKER COVER
  13. 13. POWER WINDOW SWITCH
  14. 14. POWER WINDOW SWITCH
  15. 15. PULL POCKET PANEL
  16. 16. Passenger’s:
  17. 17. PULL POCKET PANEL
  18. 18. PLASTIC COVER
  19. 19. SPEAKER
  20. 20. ADAPTER

PDF p. 1952 · 20-3

Illustration: IMMOBILIZER LABEL (for some models); GLASS; CENTRE LOWER CHANNEL; GLASS RUN CHANNEL; FRONT LOWER CHANNEL; BUSHING; OUTER HANDLE Replacement (See Page 20-7); ROD HOLDER; INNER HANDLE; INNER HANDLE ROD; OUTER HANDLE PROTECTOR; RETAINER CLIP; ROD PROTECTOR; LATCH PROTECTOR; POWER DOOR LOCK ACTUATOR; STRIKER; LATCH Replacement (See Page 20-9); LOCK KNOB; LOCK CYLINDER; POWER WINDOW MOTOR; REGULATOR
  1. 1. IMMOBILIZER LABEL (for some models)
  2. 2. GLASS
  3. 3. CENTRE LOWER CHANNEL
  4. 4. GLASS RUN CHANNEL
  5. 5. FRONT LOWER CHANNEL
  6. 6. BUSHING
  7. 7. OUTER HANDLE
    Replacement (See Page 20-7)
  8. 8. ROD HOLDER
  9. 9. INNER HANDLE
  10. 10. INNER HANDLE ROD
  11. 11. OUTER HANDLE PROTECTOR
  12. 12. RETAINER CLIP
  13. 13. ROD PROTECTOR
  14. 14. LATCH PROTECTOR
  15. 15. POWER DOOR LOCK ACTUATOR
  16. 16. STRIKER
  17. 17. LATCH
    Replacement (See Page 20-9)
  18. 18. LOCK KNOB
  19. 19. LOCK CYLINDER
  20. 20. POWER WINDOW MOTOR
  21. 21. REGULATOR

PDF p. 1953 · 20-4

Component Location Index - 5D Rear Door

Illustration: DOOR WEATHERSTRIP; REAR DOOR QUARTER INNER TRIM; REAR DOOR REAR PILLAR TRIM; UPPER CHANNEL TAPE Replacement, (See Page 20-19); DOOR MOULDING; CENTRE CHANNEL TAPE Replacement, (See Page 20-19); DOOR CENTRE SEAL; HINGE; DETENT ROD; HINGE; PLASTIC COVER; INNER WEATHERSTRIP; REAR DOOR PANEL Replacement, (See Page 20-10); POWER WINDOW SWITCH; PULL POCKET PANEL; PULL POCKET BRACKET; REAR DOOR; PROTECTION TAPE; REAR DOOR LOWER PROTECTOR Replacement, (See Page 20-18); REAR DOOR WHEEL ARCH SEAL
  1. 1. DOOR WEATHERSTRIP
  2. 2. REAR DOOR QUARTER INNER TRIM
  3. 3. REAR DOOR REAR PILLAR TRIM
  4. 4. UPPER CHANNEL TAPE Replacement, (See Page 20-19)
  5. 5. DOOR MOULDING
  6. 6. CENTRE CHANNEL TAPE Replacement, (See Page 20-19)
  7. 7. DOOR CENTRE SEAL
  8. 8. HINGE
  9. 9. DETENT ROD
  10. 10. HINGE
  11. 11. PLASTIC COVER
  12. 12. INNER WEATHERSTRIP
  13. 13. REAR DOOR PANEL
    Replacement, (See Page 20-10)
  14. 14. POWER WINDOW SWITCH
  15. 15. PULL POCKET PANEL
  16. 16. PULL POCKET BRACKET
  17. 17. REAR DOOR
  18. 18. PROTECTION TAPE
  19. 19. REAR DOOR LOWER PROTECTOR Replacement, (See Page 20-18)
  20. 20. REAR DOOR WHEEL ARCH SEAL

PDF p. 1954 · 20-5

Illustration: REAR LOWER CHANNEL; GLASS Replacement, (See Page 20-15); GLASS RUN CHANNEL; BUSHING; OUTER HANDLE Replacement, (See Page 20-11); ROD HOLDER; INNER HANDLE; LOCK KNOB; LOCK KNOB ROD; LOCK CRANK; LOCK ROD; INNER HANDLE ROD; LATCH PROTECTOR; POWER DOOR LOCK ACTUATOR; LATCH Replacement, (See Page 20-14); STRIKER; ROD PROTECTOR; OUTER HANDLE PROTECTOR; POWER WINDOW MOTOR; REGULATOR Replacement, (See Page 20-15)
  1. 1. REAR LOWER CHANNEL
  2. 2. GLASS
    Replacement, (See Page 20-15)
  3. 3. GLASS RUN CHANNEL
  4. 4. BUSHING
  5. 5. OUTER HANDLE
    Replacement, (See Page 20-11)
  6. 6. ROD HOLDER
  7. 7. INNER HANDLE
  8. 8. LOCK KNOB
  9. 9. LOCK KNOB ROD
  10. 10. LOCK CRANK
  11. 11. LOCK ROD
  12. 12. INNER HANDLE ROD
  13. 13. LATCH PROTECTOR
  14. 14. POWER DOOR LOCK ACTUATOR
  15. 15. LATCH
    Replacement, (See Page 20-14)
  16. 16. STRIKER
  17. 17. ROD PROTECTOR
  18. 18. OUTER HANDLE PROTECTOR
  19. 19. POWER WINDOW MOTOR
  20. 20. REGULATOR
    Replacement, (See Page 20-15)

PDF p. 1955 · 20-6

Front Door Panel Removal and Installation

  1. 1.
    Remove the inner handle. Take care not to scratch the door panel.

: Screw location, 1

Illustration: INNER HANDLE ROD; HOOK; HOOKS; HOOK; INNER HANDLE
  1. 1. INNER HANDLE ROD
  2. 2. HOOK
  3. 3. HOOKS
  4. 4. HOOK
  5. 5. INNER HANDLE
  1. 2.
    Remove the pull pocket panel, then disconnect the power window switch connectors.

: Screw location, 1

Illustration: PULL POCKET PANEL; HOOKS; HOOK; POWER WINDOW SWITCH CONNECTORS; HOOKS
  1. 1. PULL POCKET PANEL
  2. 2. HOOKS
  3. 3. HOOK
  4. 4. POWER WINDOW SWITCH CONNECTORS
  5. 5. HOOKS
  1. 3.
    Release the clips that hold the door panel with a commercially available trim pad remover, then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.
Illustration: Snap-on #A177, or equivalent; TRIM PAD REMOVER
  1. 1. Snap-on #A177, or equivalent
  2. 2. TRIM PAD REMOVER

: Clip locations, 7

Illustration: DOOR PANEL; LOCK KNOB
  1. 1. DOOR PANEL
  2. 2. LOCK KNOB
  1. 4.
    Install in the reverse order of removal, and note these items:
    • Replace any damaged clips.
    • Make sure the connectors are plugged in properly, and the rod is connected properly.
    • Slip the lock knob through the hole in the door panel.

PDF p. 1956 · 20-7

Front Door Outer Handle Replacement

NOTE: Put on gloves to protect your hands.

  1. 1.
    Remove:
    • Door panel
    • Plastic cover, as necessary (See Page 20-2)
  2. 2.
    Raise the glass fully.
  3. 3.
    Remove the rod protector.

: Screw location, 1

Illustration: ROD PROTECTOR; Detach the rod protector from the latch protector.
  1. 1. ROD PROTECTOR
  2. 2. Detach the rod protector from the latch protector.
  1. 4.
    Disconnect the cylinder rod. Release the retainer clip, then remove the lock cylinder.
Illustration: LOCK CYLINDER; RETAINER CLIP; CYLINDER ROD
  1. 1. LOCK CYLINDER
  2. 2. RETAINER CLIP
  3. 3. CYLINDER ROD
  1. 5.
    Remove the bolts securing the outer handle protector and outer handle.

: Bolt locations, 2

Illustration · Doors

PDF p. 1957 · 20-8

  1. 6.
    Remove the outer handle protector from the outer handle.
Illustration: OUTER HANDLE; OUTER HANDLE PROTECTOR
  1. 1. OUTER HANDLE
  2. 2. OUTER HANDLE PROTECTOR
  1. 7.

    Pull out the outer handle. Pry the outer handle rod out of its joint using diagonal cutters.

    NOTE:

    • To ease reassembly, note the distance ( A) of the outer handle rod on the joint before disconnecting it.
    • Take care not to bend the outer handle rod.
    • Use a shop towel to protect the opening in the door.
Illustration: JOINT; DIAGONAL CUTTERS; OUTER HANDLE; SHOP TOWEL; OUTER HANDLE ROD
  1. 1. JOINT
  2. 2. DIAGONAL CUTTERS
  3. 3. OUTER HANDLE
  4. 4. SHOP TOWEL
  5. 5. OUTER HANDLE ROD
  1. 8.
    Replace the bushing on the outer handle.
Illustration: BUSHING; OUTER HANDLE
  1. 1. BUSHING
  2. 2. OUTER HANDLE
  1. 9.
    Install in the reverse order of removal, and note these items:
    • Make sure each rod is connected securely.
    • Make sure the door locks and opens properly.
    • When installing the lock cylinder, leave the outer handle bolts loose so the inner protector does not interfere with the lock cylinder.
    • Install the lock cylinder retaining clip on the handle, then install the lock cylinder. Be sure the clip is fully seated in the slot on the lock cylinder.

PDF p. 1958 · 20-9

Front Door Latch Replacement

NOTE: Put on gloves to protect your hands.

  1. 1.
    Raise the glass fully.
  2. 2.
    Remove the outer handle (See Page 20-7).
  3. 3.
    Remove the glass run channel as needed from the centre lower channel. Remove the bolt, then remove the centre lower channel by pulling it downward.

: Bolt location, 1

Illustration: GLASS RUN CHANNEL; CENTRE LOWER CHANNEL
  1. 1. GLASS RUN CHANNEL
  2. 2. CENTRE LOWER CHANNEL
  1. 4.
    Detach the inner handle rod from the rod holder, and disconnect the actuator connector.

: Screw locations, 3

Illustration: LOCK ROD; OUTER HANDLE ROD; ROD HOLDER; INNER HANDLE ROD; ACTUATOR CONNECTORS; LATCH; CYLINDER ROD
  1. 1. LOCK ROD
  2. 2. OUTER HANDLE ROD
  3. 3. ROD HOLDER
  4. 4. INNER HANDLE ROD
  5. 5. ACTUATOR CONNECTORS
  6. 6. LATCH
  7. 7. CYLINDER ROD
  1. 5.
    Remove the screws, then remove the latch through the hole in the door. Take care not to bend the outer handle rod, cylinder rod, lock rod and inner handle rod.
  2. 6.
    Install in the reverse order of removal, and note these items:
    • Make sure the actuator connectors are plugged in properly, and each rod is connected securely.
    • Make sure the door locks and opens properly.

PDF p. 1959 · 20-10

Rear Door Panel Removal and Installation

  1. 1.
    Remove the inner handle. Take care not to scratch the door panel.

: Screw location, 1

Illustration: INNER HANDLE ROD; HOOK; HOOKS; HOOK; INNER HANDLE
  1. 1. INNER HANDLE ROD
  2. 2. HOOK
  3. 3. HOOKS
  4. 4. HOOK
  5. 5. INNER HANDLE
  1. 2.
    Remove the pull pocket panel, then disconnect the power window switch connector.

: Screw location, 1

Illustration: PULL POCKET PANEL; HOOKS; HOOK; POWER WINDOW SWITCH CONNECTOR; HOOKS
  1. 1. PULL POCKET PANEL
  2. 2. HOOKS
  3. 3. HOOK
  4. 4. POWER WINDOW SWITCH CONNECTOR
  5. 5. HOOKS
  1. 3.
    Lower the glass fully.
  2. 4.
    Remove the door quarter inner trim. Take care not to damage the hooks.
Illustration: HOOK; PIN; HOOK; DOOR QUARTER INNER TRIM
  1. 1. HOOK
  2. 2. PIN
  3. 3. HOOK
  4. 4. DOOR QUARTER INNER TRIM

PDF p. 1960 · 20-11

  1. 5.
    Release the clips that hold the door panel with a commercially available trim pad remover, then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.
Illustration: Snap-on #A177, or equivalent; TRIM PAD REMOVER
  1. 1. Snap-on #A177, or equivalent
  2. 2. TRIM PAD REMOVER

: Clip locations, 6

Illustration: DOOR PANEL; LOCK KNOB
  1. 1. DOOR PANEL
  2. 2. LOCK KNOB
  1. 6.
    Install in the reverse order of removal, and note these items:
    • Replace any damaged clips
    • Make sure the connector is plugged in properly, and the rod is connected properly.
    • Slip the lock knob through the hole in the door panel.

Rear Door Outer Handle Replacement

NOTE: Put on gloves to protect your hands.

  1. 1.
    Remove:
    • Door panel
    • Plastic cover, as necessary (See Page 20-4)
  2. 2.
    Raise the glass fully.
  3. 3.
    Remove the rod protector

: Screw location, 1

Illustration: ROD PROTECTOR; Detach the rod protector from the latch protector.
  1. 1. ROD PROTECTOR
  2. 2. Detach the rod protector from the latch protector.

PDF p. 1961 · 20-12

  1. 4.
    Remove the bolt, and loosen the nut, then move the rear lower channel. Remove the bolts securing the outer handle protector and outer handle.

: Bolt locations

Illustration · Doors

: Nut location, 1

Illustration: Loosen.; REAR LOWER CHANNEL; OUTER HANDLE; OUTER HANDLE PROTECTOR
  1. 1. Loosen.
  2. 2. REAR LOWER CHANNEL
  3. 3. OUTER HANDLE
  4. 4. OUTER HANDLE PROTECTOR
  1. 5.
    Remove the outer handle protector from the outer handle.
Illustration: CLIP; OUTER HANDLE; OUTER HANDLE PROTECTOR Detach the clip.
  1. 1. CLIP
  2. 2. OUTER HANDLE
  3. 3. OUTER HANDLE PROTECTOR Detach the clip.
  1. 6.

    Pull out the outer handle. Pry the outer handle rod out of its joint using diagonal cutters.

    NOTE:

    • To ease reassembly, note the distance ( A) of the outer handle rod on the joint before disconnecting it.
    • Take care not to bend the outer handle rod.
    • Use a shop towel to protect the opening in the door.
Illustration: JOINT; DIAGONAL CUTTERS; OUTER HANDLE; SHOP TOWEL; OUTER HANDLE ROD
  1. 1. JOINT
  2. 2. DIAGONAL CUTTERS
  3. 3. OUTER HANDLE
  4. 4. SHOP TOWEL
  5. 5. OUTER HANDLE ROD

PDF p. 1962 · 20-13

  1. 7.
    Replace the bushing on the outer handle.
Illustration: BUSHING; OUTER HANDLE
  1. 1. BUSHING
  2. 2. OUTER HANDLE
  1. 8.
    Install in the reverse order of removal, and note these items:
    • Make sure the outer handle rod is connected securely.
    • Make sure the door locks and opens properly.

PDF p. 1963 · 20-14

Rear Door Latch Replacement

NOTE: Put on gloves to protect your hands.

  1. 1.
    Remove:
    • Door panel (See Page 20-10)
    • Plastic cover (See Page 20-4)
    • Outer handle (See Page 20-11)
  2. 2.
    Disconnect the actuator connector.

: Screw locations, 3

Illustration: INNER HANDLE ROD; LOCK CRANK; LOCK ROD; ACTUATOR CONNECTOR; LATCH
  1. 1. INNER HANDLE ROD
  2. 2. LOCK CRANK
  3. 3. LOCK ROD
  4. 4. ACTUATOR CONNECTOR
  5. 5. LATCH
  1. 3.
    Disconnect the lock rod from the lock crank, and detach the inner handle rod and lock rod from the rod holder.
  2. 4.
    Remove the screws, then remove the latch. Take care not to bend any of the rods.
  3. 5.
    If necessary, disconnect the inner handle rod and lock rod from the latch, and detach the lock crank from the door.
  4. 6.
    Install in the reverse order of removal, and note these items:
    • Make sure the connector is plugged in properly, and each rod is connected securely.
    • Make sure the door locks and opens properly.

PDF p. 1964 · 20-15

Rear Door Glass and Regulator Replacement

NOTE: Put on gloves to protect your hands.

  1. 1.
    Remove:
    • Door panel (See Page 20-10).
    • Plastic cover (See Page 20-4).
    • Rod protector (See Page 20-11)
    • Door moulding (See Page 20-4)
  2. 2.
    Remove the door rear pillar trim. Take care not to scratch the trim.

: Screw locations, 4

Illustration: DOOR REAR PILLAR TRIM; HOOK
  1. 1. DOOR REAR PILLAR TRIM
  2. 2. HOOK
  1. 3.
    Carefully move the glass until you can see the glass mounting bolts.
  1. 4.
    Pull the glass run channel away as needed. Remove the bolt, and loosen the nut, and move the rear lower channel, then remove it from the glass.

: Nut location, 1 : Bolt location, 1

Illustration: Loosen.; GLASS RUN CHANNEL; GLASS; REAR LOWER CHANNEL
  1. 1. Loosen.
  2. 2. GLASS RUN CHANNEL
  3. 3. GLASS
  4. 4. REAR LOWER CHANNEL

PDF p. 1965 · 20-16

  1. 5.
    Loosen the glass mounting bolts. Slide the guide to the front, then remove the glass from the guide. Carefully pull the glass out through the window slot. Take care not to drop the glass inside the door.

: Bolt locations, 2

Illustration: GLASS; REGULATOR; Loosen.; GUIDE; Loosen.
  1. 1. GLASS
  2. 2. REGULATOR
  3. 3. Loosen.
  4. 4. GUIDE
  5. 5. Loosen.
  1. 6.
    Disconnect and detach the connector and harness clip from the door. Remove the bolts, and loosen the bolts, then remove the regulator through the hole in the door.

: Bolt locations

Illustration: Rearward; ROLLER GUIDE; REGULATOR; Loosen; HARNESS CLIP; Loosen; CONNECTOR; HOLE
  1. 1. Rearward
  2. 2. ROLLER GUIDE
  3. 3. REGULATOR
  4. 4. Loosen
  5. 5. HARNESS CLIP
  6. 6. Loosen
  7. 7. CONNECTOR
  8. 8. HOLE

PDF p. 1966 · 20-17

  1. 7.
    Scribe a line across the regulator and sector gear.
Illustration: SECTOR GEAR; REGULATOR; POWER WINDOW MOTOR
  1. 1. SECTOR GEAR
  2. 2. REGULATOR
  3. 3. POWER WINDOW MOTOR
  1. 8.
    Remove the bolts, then separate the power window motor and regulator. Grease the moving portions of the regulator indicated by the arrows.

: Bolt locations, 3

Illustration: POWER WINDOW MOTOR; REGULATOR
  1. 1. POWER WINDOW MOTOR
  2. 2. REGULATOR
  1. 9.
    Install in the reverse order of removal, and note these items:
    • When installing the regulator, align the hole of the roller guide toward the rear.
    • Roll the glass up and down to see if it moves freely without binding.
    • Make sure that there is no clearance between the glass and glass run channel when the glass is closed.

PDF p. 1967 · 20-18

Rear Door Lower Protector Replacement

  1. 1.
    Remove the clips and screws, then remove the door lower protector. Take care not to scratch the door. If necessary, remove the door wheel arch seal from the protector.

: Clip location, 1 : Screw locations, 3

Illustration: DOOR LOWER PROTECTOR; PROTECTOR; DOOR WHEEL ARCH SEAL
  1. 1. DOOR LOWER PROTECTOR
  2. 2. PROTECTOR
  3. 3. DOOR WHEEL ARCH SEAL
  1. 2.
    Set the door lower protector on the door, and install the clip.
  2. 3.
    Tighten the upper screw first, and tighten the remaining screws.

PDF p. 1968 · 20-19

Front and Rear Door Channel Tape Replacement

NOTE:

  • Keep dust away from the working area.
  • When working at lower temperatures, heat the door channel and door channel tape with a hair dryer.

    Door channel: about 15°C (59°F).

    Door channel tape: about 30ºC (86°F).

  • When heating the door channel tape, heat it evenly and gradually to prevent deformation.
  • When pressing the door channel tape, slowly press it from the corner to prevent air bubbles and wrinkles.
  • If there are air bubbles in the door channel tape, prick them with a pin, then release the air with your finger or a plastic squeegee.
Illustration: PIN; TRAPPED AIR
  1. 1. PIN
  2. 2. TRAPPED AIR
  • If the air bubble is more than 10 mm (0.4 in.) in diameter, peel up the door channel tape, then reapply it.
  1. 1.
    The following tools are required to replace the door channel tape.
    • Plastic squeegee
    • Alcohol
    • Sponge or Shop towel
    • Hair dryer
    • Pin
Illustration: PLASTIC SQUEEGEE; FELT
  1. 1. PLASTIC SQUEEGEE
  2. 2. FELT
  1. 2.

    Remove the following parts.

    Front door channel tape replacement:

    • Power Mirror
    • Door moulding (See Page 20-2)
    • Glass run channel, as necessary (See Page 20-3)
    • Door weatherstrip, as necessary (See Page 20-2)

Rear door upper channel tape replacement:

  • Glass (See Page 20-15)
  • Glass run channel, as necessary (See Page 20-5)
  • Door moulding (See Page 20-4)
  • Door centre seal (See Page 20-4)
  • Door rear pillar trim (See Page 20-15)
  • Door weatherstrip, as necessary (See Page 20-4)

Rear door centre channel tape replacement:

  • Glass (See Page 20-15)
  • Glass run channel, as necessary (See Page 20-5)
  • Door moulding (See Page 20-4)
  • Door centre seal (See Page 20-4)
  1. 3.

    Slowly peel up the old door channel tape while heating it with a hair dryer.

    NOTE: When replacing the door upper channel tape, replace the door centre channel tape at the same time.

  2. 4.

    Clean the door channel bonding surface with a sponge dampened in alcohol.

    NOTE: After cleaning, keep oil, grease and water from getting on the surface.

  3. 5.

    Attach the door channel tape:

    -1

-2 -3

-4

Peel the edge of the adhesive backing from the channel tape.

Fit the door channel tape to the door channel. Apply the door channel tape to the door channel while peeling the adhesive backing from it a little at a time. Check that the channel tape is parallel with the door channel. Push firmly on the door channel tape with a plastic squeegee (felt side).

NOTE: To prevent air bubbles, slowly press the door channel tape around the door frame corner.

  1. 6.
    As necessary, repeat the preceding steps.
  2. 7.
    Reinstall all remaining removed parts.
  3. 8.
    Check that the body colour on the door channel is covered by the door channel tape.
  4. 9.
    Check for water leaks. Do not squeeze the tip of the hose.

PDF p. 1969 · 20-20

Front door upper channel tape and centre channel tape:

Apply the door channel tapes in numbered sequence.

Illustration: UPPER CHANNEL TAPE; UPPER CHANNEL TAPE; Align.; Align.; CENTRE CHANNEL TAPE; UPPER CHANNEL TAPE; CENTRE CHANNEL TAPE; CENTRE CHANNEL TAPE; Align.; UPPER CHANNEL TAPE
  1. 1. UPPER CHANNEL TAPE
  2. 2. UPPER CHANNEL TAPE
  3. 3. Align.
  4. 4. Align.
  5. 5. CENTRE CHANNEL TAPE
  6. 6. UPPER CHANNEL TAPE
  7. 7. CENTRE CHANNEL TAPE
  8. 8. CENTRE CHANNEL TAPE
  9. 9. Align.
  10. 10. UPPER CHANNEL TAPE

NOTE: Press in numbered sequence.

Illustration: UPPER CHANNEL TAPE; Inside; Inside; CENTRE CHANNEL TAPE
  1. 1. UPPER CHANNEL TAPE
  2. 2. Inside
  3. 3. Inside
  4. 4. CENTRE CHANNEL TAPE

PDF p. 1970 · 20-21

Rear door upper channel tape and centre channel tape:

Apply the door channel tapes in numbered sequence.

Illustration: UPPER CHANNEL TAPE; CENTRE CHANNEL TAPE; Align.; UPPER CHANNEL TAPE; Align.; UPPER CHANNEL TAPE; Align.; (1) UPPER CHANNEL TAPE; Align.; CENTRE CHANNEL TAPE; (2) CENTRE CHANNEL TAPE
  1. 1. UPPER CHANNEL TAPE
  2. 2. CENTRE CHANNEL TAPE
  3. 3. Align.
  4. 4. UPPER CHANNEL TAPE
  5. 5. Align.
  6. 6. UPPER CHANNEL TAPE
  7. 7. Align.
  8. 8. (1) UPPER CHANNEL TAPE
  9. 9. Align.
  10. 10. CENTRE CHANNEL TAPE
  11. 11. (2) CENTRE CHANNEL TAPE

NOTE: Press in numbered sequence.

Illustration: Inside; Inside
  1. 1. Inside
  2. 2. Inside