Workshop manual

Rear Side Outer Panel

Replacement

Body Repair Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 1644, 1645, 1646, 1647, 1648, 1649 (manual pages 4-34 to 4-39)

PDF p. 1644 · 4-34

  1. 1.
    Remove the related parts.
    • Rear bumper.
    • Tailgate.
    • Taillight.
    • Rear seat.
    • Trim, trim panel and luggage compartment fitting.
    • Rear seat belt.
    • Fuel fill pipe (left side only).
  1. 2.

    Pull out and straighten the damaged area.

    NOTE: Carefully check the inner pillar and rear pillar gutter for position and damage. Pull out the inner panel by cutting the outer if necessary.

    • Jack-up the body and place safety stands at the four designated support points.
    • Pull out the damaged rear side outer panel with the frame straightener, then pull out and straighten the inner panel and rear wheelhouse.

NOTE: Be careful not to pull out more than necessary.

  • After pulling, check the inner pillar and rear panel gutter position using the body dimensional drawings (see section 6).
  1. 3.

    Peel off the undercoat.

    Heat the undercoat at the weld areas of the rear wheel house with a gas torch and peel off the undercoat with metal spatula.

  1. 4.
    Cut and pry off the rear side outer panel.
    • Cut at the centre pillar and side sill with a handsaw.
    • Cut the panel from the body with a chisel, leaving the weld flange at the inner panel intact.

NOTE: Do not cut or damage the centre pillar stiffener, inner panel, rear damper stiffener and rear pillar gutter.

  • Cut at the side sill or wheel arch according to the extent of the damage.
  • Centre punch around the spot weld imprints on the remaining flange.
  • Drill out the spot welds with the spot cutter.
  • Pry off the welded flange sections using a chisel.
Illustration: CENTRE PILLAR STIFFENER; REAR DAMPER STIFFENER; INNER PANEL; REAR PILLAR GUTTER; REAR PANEL; REAR PILLAR STIFFENER; MASTIC SEALERS; OUTER PANEL
  1. 1. CENTRE PILLAR STIFFENER
  2. 2. REAR DAMPER STIFFENER
  3. 3. INNER PANEL
  4. 4. REAR PILLAR GUTTER
  5. 5. REAR PANEL
  6. 6. REAR PILLAR STIFFENER
  7. 7. MASTIC SEALERS
  8. 8. OUTER PANEL

PDF p. 1645 · 4-35

  1. 5.
    Check the centre pillar stiffener for position and damage. Replace the centre pillar stiffener if necessary.
  2. 6.
    Cut and drill out the spot welds and pry off the centre pillar stiffener.
    • Leave the centre pillar lower stiffener attached to the inside sill.
    • Cut at over the centre pillar upper anchor
Illustration: CENTRE PILLAR UPPER ANCHOR; Cut line; CENTRE PILLAR STIFFENER; CENTRE PILLAR LOWER STIFFENER
  1. 1. CENTRE PILLAR UPPER ANCHOR
  2. 2. Cut line
  3. 3. CENTRE PILLAR STIFFENER
  4. 4. CENTRE PILLAR LOWER STIFFENER
  1. 7.
    Check the rear pillar gutter for position and damage. Replace the rear pillar gutter if necessary.
  2. 8.
    Cut and drill out the spot welds and pry off the rear pillar gutter.
    • Cut the rear pillar gutter at under portion from the outer panel cut line.
Illustration: Cut line; REAR PILLAR GUTTER
  1. 1. Cut line
  2. 2. REAR PILLAR GUTTER

PDF p. 1646 · 4-36

  1. 9.
    Straighten the inner panel and related parts.
    • Use a slide hammer to even out the damaged areas of the rear wheel arch.
    • Fill the holes drilled by MIG or gas welding.
  • Level and finish burrs, etc., with a disc sander.
  1. 10.
    Cut the new centre pillar stiffener so it overlaps the body side stiffener by approximately 20 mm (0.8 in).
Illustration: Overlap 20 mm (0.8 in); CENTRE PILLAR STIFFENER (New part)
  1. 1. Overlap 20 mm (0.8 in)
  2. 2. CENTRE PILLAR STIFFENER (New part)
  1. 11.
    Cut the new rear pillar gutter so it overlaps the body side gutter by approximately 20 mm (0.8 in).
Illustration: Overlap 20 mm (0.8 in); REAR PILLAR GUTTER (New part)
  1. 1. Overlap 20 mm (0.8 in)
  2. 2. REAR PILLAR GUTTER (New part)
  1. 12.
    Clamp and check the centre pillar stiffener and rear pillar gutter in its correct position using the body dimensional drawings (see section 6).
    • Remove the undercoat from both sides of the weld flange with a sander to expose the steel plate.

NOTE: Apply the spot sealer to the welding surface when spot welding.

  1. 13.
    Temporarily spot weld the centre pillar stiffener and rear pillar gutter at the clamped positions.

PDF p. 1647 · 4-37

  1. 14.
    Cut and clamp the rear part.
    • Cut so that the repair part overlaps the side sill by 30 mm (1.2 in.).
    • Remove the undercoat from both sides of the weld flange with a sander to expose the steel plate.
  2. 15.
    Check the position of the repair part using the body dimensional drawings (see section 6).
  3. 16.
    Remove the repair part and weld the new centre pillar stiffener and the new rear pillar gutter.
Illustration: Fillet welding; CENTRE PILLAR STIFFENER (New part)
  1. 1. Fillet welding
  2. 2. CENTRE PILLAR STIFFENER (New part)
Illustration: Fillet welding; REAR PILLAR GUTTER (New part)
  1. 1. Fillet welding
  2. 2. REAR PILLAR GUTTER (New part)
  1. 17.
    Apply body paint to the back of the repair part.
    • See Paint Repair section.

PDF p. 1648 · 4-38

  1. 18.
    Apply the reinforcement tape to the inside face of the

repair part as shown (right side only).

NOTE:

  • Before applying, clean the repair part surface with a sponge dampened in alcohol.
  • After applying, heat the reinforcement tape equality for about 30 minutes with a drier.
Illustration: REINFORCEMENT TAPE (P/N 67112-S50-310)
  1. 1. REINFORCEMENT TAPE (P/N 67112-S50-310)
  1. 19.
    Set and tack weld repair part.
    • Attach the patch at cut section of the rear pillar (body side) and plug weld it.

NOTE: Apply the spot sealer to the welding surface when spot welding.

  1. 20.

    Remove the vice-grips and check the alignment of the taillight, door, rear bumper and tailgate.

    NOTE:

    • Check for flushness of the front fender, door and the rear fender, taillight, rear bumper and make sure that the body lines flow smoothly.
  1. 21.
    Perform the main welding.
  • Make 20% to 30% more spot welds than there were holes drilled.

NOTE: If there is not room for spot welds,

compensate by using MIG welds.

  • Make 5 mm (0.2 in.) holes in the MIG weld hole with the repair part and the inner panel and centre pillar stiffener with a MIG welder.
  • Weld the outer panel at the centre pillar and side sill with a MIG welder.
Illustration: Butt welding; PATCH; OUTER PANEL (Repair part); Fillet welding; Overlap 30 mm (1.2 in.)
  1. 1. Butt welding
  2. 2. PATCH
  3. 3. OUTER PANEL (Repair part)
  4. 4. Fillet welding
  5. 5. Overlap 30 mm (1.2 in.)

PDF p. 1649 · 4-39

Illustration: Butt welding; PATCH; OUTER PANEL (Repair part)
  1. 1. Butt welding
  2. 2. PATCH
  3. 3. OUTER PANEL (Repair part)
  1. 22.
    Finish the welded areas.
    • Level the MIG welded areas with a disc sander.
  • Even out high areas with a hammer. Be careful not to deform them.
  • Even out the spot welded flange areas with a hammer and dolly.
  • Fill in deformations and level differences of the welded areas with solder or putty, then finish.
  1. 23.

    Apply the sealer (see section 5).

    Apply sealer to the fuel filler sections, tailgate opening joint and around the taillight area of the rear pillar gutter.

  1. 24.
    Apply paint. See Paint Repair section.
  1. 25.

    Apply the undercoat.

    Apply undercoat to the wheelhouse and apply anti-rust agent to the inside of the outer panel and rear pillar gutter (see section 7).

  2. 26.
    Install the related parts in the reverse order in which they were removed.
  3. 27.
    Inspect, check and clean.
    • Adjust the clearance with the door and tailgate then adjust the level differences and fit.

      Check operation.

    • Test for leaks in the trunk and passenger compartments.
    • Check the quarter glass for water leaks.
    • Clean the trunk floor.