Workshop manual

Transmission Housing

Disassembly

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 491, 492, 493, 494 (manual pages 13-18 to 13-21)

PDF p. 491 · 13-18

  1. 1.
    Remove the transfer assembly or left side cover. 2WD Model:
Illustration: LEFT SIDE COVER; O-RING, Replace
  1. 1. LEFT SIDE COVER
  2. 2. O-RING, Replace

4WD Model:

Illustration: DOWEL PIN; O-RING, Replace; TRANSFER ASSEMBLY
  1. 1. DOWEL PIN
  2. 2. O-RING, Replace
  3. 3. TRANSFER ASSEMBLY
  1. 2.
    Remove the shift arm cover assembly and wipe it clean of the sealant.
Illustration: SHIFT ARM COVER ASSEMBLY; 10 x 12 mm DOWEL PIN
  1. 1. SHIFT ARM COVER ASSEMBLY
  2. 2. 10 x 12 mm DOWEL PIN
  1. 3.
    Remove the interlock bolt.
Illustration: SELECT LEVER; INTERLOCK BOLT; SELECT ARM; SHIFT ARM SHAFT; SHIFT ARM A
  1. 1. SELECT LEVER
  2. 2. INTERLOCK BOLT
  3. 3. SELECT ARM
  4. 4. SHIFT ARM SHAFT
  5. 5. SHIFT ARM A
  1. 4.
    Turn the select lever counterclockwise, then remove the shift arm A finger from the groove of the shift forks.
  2. 5.
    Turn the shift arm shaft counterclockwise and remove the select arm finger from the groove of the shift arm A, then remove the shift arm shaft assembly.
  3. 6.
    Remove the vehicle speed sensor (VSS).
Illustration: O-RING, Replace; VEHICLE SPEED SENSOR
  1. 1. O-RING, Replace
  2. 2. VEHICLE SPEED SENSOR

PDF p. 492 · 13-19

  1. 7.
    Remove the set ball screws, washers, springs, steel balls and back-up light switch.
Illustration: WASHER, Replace; STEEL BALL 5/16 in D.; WASHER, Replace; SET BALL SCREW; SPRING, 26.1 mm (1.03 in) L; BACK-UP LIGHT SWITCH
  1. 1. WASHER, Replace
  2. 2. STEEL BALL 5/16 in D.
  3. 3. WASHER, Replace
  4. 4. SET BALL SCREW
  5. 5. SPRING, 26.1 mm (1.03 in) L
  6. 6. BACK-UP LIGHT SWITCH
  1. 8.
    Remove the flange bolt, drain plug and filler plug.
Illustration: FILLER PLUG; DRAIN PLUG; WASHER, Replace; WASHER, Replace; FLANGE BOLT
  1. 1. FILLER PLUG
  2. 2. DRAIN PLUG
  3. 3. WASHER, Replace
  4. 4. WASHER, Replace
  5. 5. FLANGE BOLT
  1. 9.
    Remove the transmission housing mounting bolts in a crisscross pattern in several steps.
Illustration: TRANSMISSION HANGER; TRANSMISSION HOUSING MOUNTING BOLT
  1. 1. TRANSMISSION HANGER
  2. 2. TRANSMISSION HOUSING MOUNTING BOLT
  1. 10.
    Remove the 32 mm sealing bolt.
Illustration: TRANSMISSION HOUSING; 32 mm SEALING BOLT; SNAP RING PLIERS, 07LAC-0010100; SNAP RING; CLUTCH HOUSING; DOWEL PINS
  1. 1. TRANSMISSION HOUSING
  2. 2. 32 mm SEALING BOLT
  3. 3. SNAP RING PLIERS, 07LAC-0010100
  4. 4. SNAP RING
  5. 5. CLUTCH HOUSING
  6. 6. DOWEL PINS
  1. 11.
    Expand the snap ring on the countershaft ball bearing and remove it from the groove using a pair of snap ring pliers.
  2. 12.
    Separate the transmission housing from the clutch housing.
  3. 13.
    Remove the dowel pins and wipe it clean of the sealant.

PDF p. 493 · 13-20

  1. 14.
    Remove the oil gutter plate, 78 mm shim and oil guide M plate.
Illustration: 78mm SHIM; OIL GUTTER PLATE; OIL GUIDE M PLATE
  1. 1. 78mm SHIM
  2. 2. OIL GUTTER PLATE
  3. 3. OIL GUIDE M PLATE
  1. 15.
    Remove the select spring bolt.
Illustration: SELECT SPRING BOLT
  1. 1. SELECT SPRING BOLT
  1. 16.
    Remove the spring pin using the pin driver to push it half way out, then pull out the spring pin using a nipper.
Illustration: PIN DRIVER, 5.0 mm, 07GAD-PG20100; SPRING PIN, Replace
  1. 1. PIN DRIVER, 5.0 mm, 07GAD-PG20100
  2. 2. SPRING PIN, Replace
  1. 17.
    Remove the select lever, springs, washer and select arm
Illustration: SELECT LEVER; OIL SEAL, Replace; SELECT RETURN SPRING; 5TH/REVERSE SELECT RETURN SPRING; THRUST WASHER; SELECT ARM
  1. 1. SELECT LEVER
  2. 2. OIL SEAL, Replace
  3. 3. SELECT RETURN SPRING
  4. 4. 5TH/REVERSE SELECT RETURN SPRING
  5. 5. THRUST WASHER
  6. 6. SELECT ARM
  1. 18.
    Remove the oil seal.

PDF p. 494 · 13-21

  1. 19.
    Remove the reverse lock cam.
Illustration: REVERSE LOCK CAM
  1. 1. REVERSE LOCK CAM
  1. 20.
    If necessary, check the clearance of the reverse shift holder (See page 13-24).
  2. 21.
    Remove the reverse shift holder.
Illustration: REVERSE SHIFT HOLDER
  1. 1. REVERSE SHIFT HOLDER
  1. 22.
    Remove the reverse gear shaft and the reverse idler gear.
Illustration: REVERSE GEAR SHAFT; REVERSE IDLER GEAR
  1. 1. REVERSE GEAR SHAFT
  2. 2. REVERSE IDLER GEAR
  1. 23.

    Remove the mainshaft and countershaft assemblies with the shift forks, from the clutch housing

    NOTE: Before removing the mainshaft and countershaft assemblies, tape the mainshaft spline to protect it.

Illustration: MAINSHAFT ASSEMBLY; COUNTERSHAFT ASSEMBLY; SHIFT FORKS; CLUTCH HOUSING; SPRING WASHER; WASHER; Tape the main shaft splines
  1. 1. MAINSHAFT ASSEMBLY
  2. 2. COUNTERSHAFT ASSEMBLY
  3. 3. SHIFT FORKS
  4. 4. CLUTCH HOUSING
  5. 5. SPRING WASHER
  6. 6. WASHER
  7. 7. Tape the main shaft splines
  1. 24.
    Remove the differential assembly.
Illustration: DIFFERENTIAL ASSEMBLY
  1. 1. DIFFERENTIAL ASSEMBLY