Workshop manual

Idle Control System

Idle Speed Setting

Supplement 2000 (5-door model) · source: HRV_Workshop_Manual.pdf, PDF pages 1884, 1885, 1886 (manual pages 11-103 to 11-105)

PDF p. 1884 · 11-103

D16W1 engine:

Inspection/Adjustment

Adjust the idle speed by means of a Honda PGM-TESTER. If not, check the following:

NOTE: Before setting the idle speed, check the following items:

  • The MIL has not been reported on.
  • Ignition timing
  • Spark plugs
  • Air cleaner
  • PCV System
  1. 1.
    Connect a tachometer.
Illustration: TEST TACHOMETER CONNECTOR; TACHOMETER; BATTERY
  1. 1. TEST TACHOMETER CONNECTOR
  2. 2. TACHOMETER
  3. 3. BATTERY
  1. 2.
    Start the engine. Hold the engine at 3,000 rpm (min-1) with no load until the radiator fan comes on, then let it idle.
  2. 3.

    Check the idle speed with no-load conditions:

    head-lights, blow fan, rear defogger, radiator fan, and air conditioner not operating.

Idle speed should be:

M/T A/T

750 + 50 rpm (min-1)

700 + 50 rpm (min-1) (in N or P position)

  1. 4.
    Adjust the idle speed, if necessary, by turning the idle adjusting screw ½-turn clockwise or counterclockwise.
Illustration: CAP; IDLE ADJUSTING SCREW
  1. 1. CAP
  2. 2. IDLE ADJUSTING SCREW
  1. 5.

    After a ½-turn of the idle adjusting screw, check the idle speed again. If it is out of spec, turn the idle adjusting screw ½-turn again.

    NOTE: Do not turn the idle adjusting screw more than ½-turn without checking the idle speed.

  2. 6.

    Idle the engine for one minute with the heater fan switch at HI and air conditioner on, then check the idle speed.

    Idle speed should be:

M/T A/T

or P

810 + 50 rpm (min-1) 810 + 50rpm (min-1) (in N

position)

NOTE:

  • Do not turn the idle adjusting screw when the air conditioner is on.
  • (See Page 11-42) for System Troubleshooting Guide if the idle speed is not within specification.

PDF p. 1885 · 11-104

D16W5 engine:

Inspection/Adjustment

NOTE: Before setting the idle speed, check the following items:

  • The MIL has not been reported on.
  • Ignition timing
  • Spark plugs
  • Air cleaner
  • PCV System
  1. 1.
    Connect the tachometer.
Illustration: TEST TACHOMETER CONNECTOR; TACHOMETER; BATTERY
  1. 1. TEST TACHOMETER CONNECTOR
  2. 2. TACHOMETER
  3. 3. BATTERY
  1. 2.
    Start the engine. Hold the engine at 3,000 rpm (min-1) with no load (in neutral) until the radiator fan comes on, then let it idle.
  2. 3.
    Disconnect the 2P connector from the Idle Air Control (IAC) Valve.
Illustration: IAC VALVE
  1. 1. IAC VALVE
  1. 4.
    Start the engine with the accelerator pedal slightly depressed. Stabilise the engine speed at 1,000 rpm (min-1), then slowly release the pedal until the engine idles.
  1. 5.
    Check idling in no-load conditions: headlights, blower fan, rear defogger, radiator fan, and air conditioner are not operating.

Idle speed should be:

450 + 50 rpm (min-1) (in neutral)

Adjust the idle speed, if necessary, by turning the idle adjusting screw.

NOTE: After adjusting the idle speed in this step, check the ignition timing (see section 4). If it is out of spec, go back to step 4.

Illustration: CAP; IDLE ADJUSTING SCREW
  1. 1. CAP
  2. 2. IDLE ADJUSTING SCREW
  1. 6.
    Turn the ignition switch OFF.
  2. 7.
    Reconnect the 2P connector on the IAC valve, then remove the BACK UP (7.5 A) fuse in the under-hood fuse/relay box for 10 seconds to reset the ECM.

PDF p. 1886 · 11-105

  1. 8.

    Restart and idle the engine with no-load conditions for one minute, then check the idle speed.

    Idle Speed should be:

    750 + 50 rpm (min-1) (in neutral)

  2. 9.

    Idle the engine for one minute with headlights (Low) ON and check the idle speed.

    Idle Speed should be:

    750 + 50 rpm (min-1) (in neutral)

  3. 10.

    Turn the headlights off.

    Idle the engine for one minute with the heater fan switch at HI and air conditioner on, then check the idle speed.

    Idle Speed should be:

    810 + 50 rpm (min-1) (in neutral)

    NOTE: (See Page 11-42) for System Troubleshooting Guide if the idle speed is not within specification.