Workshop manual

Engine Oil

Shop Manual 1999 · source: HRV_Workshop_Manual.pdf, PDF pages 301, 302 (manual pages 8-5 to 8-6)

PDF p. 301 · 8-5

Inspection

  1. 1.
    Park the vehicle on level ground, and turn off the engine. Allow the oil a few minutes to drain back into the oil pan so that the dipstick will show the actual level.
  2. 2.
    Make certain that the oil level indicated on the dipstick is between the upper and lower marks.
Illustration: DIPSTICK; UPPER; LOWER
  1. 1. DIPSTICK
  2. 2. UPPER
  3. 3. LOWER
  1. 3.
    If the level has dropped close to the lower mark, add oil until it reaches the upper mark.

Replacement

  1. 1.
    Warm up the engine.
  2. 2.
    Drain the engine oil.

Europe, Australia and South Africa models:

Illustration: WASHER. Replace.; DRAIN BOLT, 39 Nm (4.0 kgf/m, 29 lbf/ft). Do not overtighten.
  1. 1. WASHER. Replace.
  2. 2. DRAIN BOLT, 39 Nm (4.0 kgf/m, 29 lbf/ft). Do not overtighten.

Except Europe, Australia and South Africa models:

Illustration: WASHER. Replace.; DRAIN BOLT, 44 Nm (4.5 kgf/m, 33 lbf/ft). Do not over tighten.
  1. 1. WASHER. Replace.
  2. 2. DRAIN BOLT, 44 Nm (4.5 kgf/m, 33 lbf/ft). Do not over tighten.

PDF p. 302 · 8-6

  1. 3.
    Reinstall the drain plug with new washer, and refill with the recommended oil.

Requirement

Always use a fuel efficient oil that says “API Service SG, SH or SJ”.

SAE Viscosity; See chart in right hand column.

Capacity

Europe, Australia and South Africa models:

3.0 l (3.2 US qt, 2.6 Imp qt) at oil change.

3.3 l (3.5 US qt, 2.9 Imp qt) at oil change, including filter. 3.7 l (3.9 US qt, 3.3 Imp qt) after engine overhaul.

Except Europe, Australia and South Africa models:

3.3 l (3.5 US qt, 2.9 Imp qt) at oil change.

3.6 l (3.8 US qt, 3.2 Imp qt) at oil change, including filter. 4.3 l (4.5 US qt, 3.8 Imp qt) after engine overhaul.

Change Interval

Europe model:

Every 15,000 km (9,000 miles) or 12 months (Normal condition).

Every 7,500 km (6,000 miles) or 6 months (Severe conditions).

Australia model:

Every 10,000 km (6,000 miles) or 12 months (Normal condition).

Every 5,000 km (3,000 miles) or 6 months (Severe conditions).

Except Europe and Australia models:

Every 7,500 km (6,000 miles) or 6 months

Engine Oil SAE Viscosity for Outside Temperature Ranges:

Illustration · Engine Oil SAE Viscosity for Outside Temperature Ranges

Ambient temperature ranges

  1. 4.
    Fill the engine with oil up to the specified level, run the engine for more than three minutes, then check for oil leakage and oil level.

Oil Filter

Replacement

  1. 1.
    Remove the oil filter with the special oil filter wrench.
  2. 2.

    Inspect the threads and rubber seal on the new filter. Wipe off the seat on the engine block, then apply a light coat of oil to the filter rubber seal.

    NOTE: Use only filters with built-in bypass system.

Illustration: Apply oil to rubber seal before installing.; Inspect threads and rubber seal surface.
  1. 1. Apply oil to rubber seal before installing.
  2. 2. Inspect threads and rubber seal surface.